無鉛焊錫機的詳細描述：無鉛電焊臺
參數設置
1.出錫速度SPEED
采用撥碼開關設置，按壓撥盤上的“+”，對應位的數字增加一個數字；“-”對應位數字減少一個數字。
出錫速度為1位設置，0-9表示出錫速度約2.7mm/s-27mm/s（36º/s-360º/s）.分辨率為2.7mm/s即每1數值代表出錫速度2.7mm/s（36º/s）。
如：設置為0時，出錫速度zui慢，為2.7mm/s（36º/s）；設置為1時，速度為5.4mm/s（72º/s）；。。。。。。設置為9時，出錫速度zui快，為27mm/s（360º/s）。撥動碼開關“SPEED"，根據工作需求，選折相應的數值。
可調范圍：約2.7mm/s-27mm/s（36º/s-360º/s）
Technical data:
1.Feed speed
Adopt data-chosen-switches settings,press "+",the corresponding bit numbers increased by a number; "-" to reduce a number.
Feed speed is one number setting, 0-9 mean the feed speed is
about 2.7mm/s-27mm/s（36º/s-360º/s）. Resolution is 2.7mm/s,this mean each one number represents the tin-speed is 2.7mm/s（36º/s）.
For example,Set 0,the tin-speed is the lowest 2.7mm/s（36º/s）. Set 1,the tin-speed is 5.4mm/s（72º/s）.......Set 9,the tin-speed is the fastest,is 27mm/s（360º/s）.Dial the switch"SPEED",According to your work requirements,choose the number.
The adjustable range:about 2.7mm/s-27mm/s（36º/s-360º/s）
2.出錫量LENGTH
出錫量采用角度制，即用電機所轉的角度來表示出錫的長度。
出錫量為3位設置，001-999表示出錫長度為0.15-150mm；分辨率為0.15mm（1.8度）即每1數值表示0.15mm（1.8度）.數值設置方式同出錫速度.
如:設置數值為001時,出錫角度為1.8度,出錫長度為0.15mm;設置數值為002時,出錫角度為3.6度,長度為0.3mm,`````````````選擇數值為999時zui長,出錫角度1798.2度,長度約為150mm
撥動撥碼開關"LENGTH"根據工作需求,選擇相應的數值.
可調范圍:0-150mm
2.Length
The Feeding speed adopt degree measure,the angle turn by motor show the length of the tin.
The Feeding speed setting by 3 numbers,001-009 mean the length is 0.15-150mm,resolution is 0.15mm（1.8º）.That each number mean 0.15mm（1.8º）.the number setting method is same as Feed speed.
For example:Set 001,the feeding angle is 1.8º,the feeding length is 0.15mm,Set 002,the feeding angle 3.6º,the feeding length is 0.3mm..........choose 9999,the angle is 1798.2º,the length is 150mm.Dial the switch "LENGTH",According to your work requirements,choose the number.
The adjustable range:0-150mm
3.出錫間隔時間INTERVAL TINE
出錫間隔時間是指自動出錫在兩次以上時,每次出錫之間的間隔時間,間隔時間采用1位數設置,0-9表示0-2.7S,分辯率為0.3S.即每1數值表示為0.3S.數值設置方式同出錫速度.
如:設置數值為1時.間隔時間為0.3秒;設置數值為2時,間隔時間為0.6秒; ```````````設置數值為9時時間zui長,間隔時間為2.7秒;
撥動撥碼開關'INTERVAL TIME"進行數值選擇.
可調范圍:0-2.7S
Feeding interval time
The feeding interval time mean automatic feeding more than 2 times,the each time interval between the feeding,the interval time adopt one number setting,0-9 mean 0-2.7s,resolution is 0.3s,that mean each 1 number represent 0.3s.the number setting method is same as Feed speed.
For example:when set number 1,the interval time is 0.3s,when set number 2,the interval time is 0.6s.........when set number 9,the interval time is 2.7s
Dial switch"INTERVAL TIME",according to your work requirements,choose the number.
The adjustable range:0-2.7s
4.出錫方式設置MODE
撥動撥碼開關"MODE"選擇相應的數值.
出錫方式為1位設置,數值選擇方式同上.每個數值對應功能如下;
0:手動出錫 1:自云出錫1次
2:自動出錫2次 3:自動出錫3次
4:自動出錫4次 5:自動出錫5次
6:自動出錫6次 7:自動出錫7次
8:自動出錫8次 9:自動出錫9次
每次出錫后都會回錫.
Feeding mode
Dial the switch"MODE"choose the number.
When Feeding mode is 1,the number setting method is same as Feed speed. Each number mean:
0:manual feeding 1:Auto feeding 1 times
2:Auto feeding 2 times 3:Auto feeding 3 times
4.Auto feeding 4 times 5:Auto feeding 5 times
6.Auto feeding 6 times 7:Auto feeding 7 times
8.Auto feeding 8 times 9:Auto feeding 9 times
Each auto feeding will back feeding.
5.回錫時間RETURN
撥動撥碼開關"RETURN"選技相應的數值.
回錫時間為1位數設置.0-9表示0-0.9S,分辯率為0.1S即每1數值表示0.1S.在回錫時回錫速度一定.不可以設整,為360°/S.
如:設置數值為0時,回錫時間為0S,回錫長度為0mm;設置數值為1時,回錫時間為0.1S,回錫長度約為2.8MM;設置數值為2時,回錫時間為0.2S,回錫長度約5.6mm;.``````````````設置數值為9時,回錫時間為0.9S,回錫長度約25mm.
可調范圍:0-0.9S（約0-25mm）.
6.出錫力度
由于出錫力度不足,錫線不被自動送出時,可調節機器上蓋的壓力調節螺絲增強出錫力度----順時針節調節;由于力度太大,而使錫線被擠壓變形時,可減弱出錫力度---------逆時針調節.
Back feeding:
Dial the switch "RETURN" choose the number.
Backing time is 1 number setting,0-9 mean 0-0.9s,resolution is 0.1s,that mean each 1 number mean 0.1s,when backing feeding ,the number should not set integral,is 360°/S.
For example:
如:設置數值為0時,回錫時間為0S,回錫長度為0mm;設置數值為1時,回錫時間為0.1S,回錫長度約為2.8MM;設置數值為2時,回錫時間為0.2S,回錫長度約5.6mm;.``````````````設置數值為9時,回錫時間為0.9S,回錫長度約25mm.
可調范圍:0-0.9S（約0-25mm）.
7.出錫力度
由于出錫力度不足,錫線不被自動送出時,可調節機器上蓋的壓力調節螺絲增強出錫力度----順時針節調節;由于力度太大,而使錫線被擠壓變形時,可減弱出錫力度---------逆時針調節.
When set 0,the backing time is 0s,the length is 0mm,set 1,the backing time is 0.1s,the length is 2.8mm,set 2,the backing time is 0.2s,the length is 5.6mm.......set 9,the backing time is 0.9s,the length is 25mm
The adjustable range:0-0.9s（about 0-25mm）
