污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
山東威蘭圖新能源科技有限公司
會員1.png)
山東威蘭圖新能源科技有限公司
| 參 考 價 | 面議 |
產品型號
品 牌
廠商性質其他
所 在 地
聯系方式：寧經理查看聯系方式
更新時間：2023-03-26 15:58:14瀏覽次數：344次
聯系我時，請告知來自 環保在線技術指標1
技術指標
1.口徑：1/4″~2 1/2″
2.壓力：150LB~4500LB
3.閥體材質：
碳素鋼 -50℃～425℃
合金鋼 -50℃～610℃
不銹鋼 -50℃～700℃
4.連接方式：對焊、承插焊、外螺紋、卡套等
5.適用介質：水、蒸汽及各種腐蝕介質
Technical indicators
1.size: 1/4″~2 1/2″
2. Pressure: 150LB~4500LB
3. Body material
Carbon steel -50℃～425℃
Alloy steel -50℃～610℃
Stainless steel -50℃～700℃
4. End connection: Butt-welded,
Socket-welded, External thread, Card set
5. Applicable medium：water, steam
And corrosive medium
性能特點： Performance characteristics
1、優質鍛件并經固融處理的體，確保無內外紋
2、座堆焊估基硬質合金，極大地提高了高溫硬度和抗介質沖蝕能力
3、閥采用結鉻鎢銅球，具有很高的高溫硬度，使其抗介質沖蝕能力大大優于普通針型閥
4、經造的閥桿，柔性和強度不同一般，壓加工的螺紋位于填料之上，進免了與介質接觸，光桿部位經精處理
不僅與填料緊密接觸，保證了密封無外漏，而且減少了開啟力矩，門啟閉時靈活自如
5、設計的中口金屬密封墊，經特殊工藝調質處理，確保高溫高壓下的良好密封
6、致配性優良的柔性石墨填料，確保了高溫高壓下無外
7、執行標準： ASMI B16．34
1. The ve body has quality forging and after melts processing firmly. This can guarantee that does not have the inside and ous
ide cra
ve seat built-up welding cobalt base hard alloy, this can enhance the high temperature degree of hardness and anti-med
2、 The ium eroding ability enormously.
3. The valve petal uses the cobalt chrome tungsten steel ball. It has the very high high temperature degree of hardness. This can
cause its anti-medium eroding ablity to surpass the ordinary needle valve
4. The valve stem is forged, its flexibility and intensity different general. The trundle processed thread located at padding above
this can avoid contact with the medium The polished rod spot is processed by correct gridding. This can guarantee the close con
tact with the padding. The valve has no outside leaks. This design can also reduce the opening moment of force and the valve op
ens shuts time nimble freely.
5. The unique design mouth metal gasket is manufactured by special craft quenching treatment. This can guarantee the good se
al in the high temperature and high pressure
6. The compact fine flexible graphite padding, has guaranteed the valve has not outside leaks in the high temperature high press
ure
7. Standard: ASMI B16. 34
剖視圖
尺寸表
通經 | 結構長度A | 中心高B | 手柄長度C | 重量KG |
DN10/3/8’’ | 120 | 245 | 180 | 5.3 |
DN15/1/2’’ | 120 | 245 | 180 | 6.8 |
DN20/3/4/’’ | 170 | 350 | 180 | 9.7 |
DN25/1’’ | 170 | 350 | 180 | 9.7 |
DN32/1 1/4’’ | 170 | 350 | 180 | 10.4 |
材質表
部件/類別 | F105 | F22 | WB36 | F91 | F92 | F316 | F316H | F347H |
閥體 | F105 | F22 | WB36 | F91 | F92 | F316 | F316H | F347H |
閥座 | 司太立 | 司太立 | 司太立 | 司太立 | 司太立 | 司太立 | 司太立 | 司太立 |
閥瓣 | Co-Cr-W鋼球Co-Cr-W Steel ball | Co-Cr-W鋼球Co-Cr-W Steel ball | Co-Cr-W鋼球Co-Cr-W Steel ball | Co-Cr-W鋼球Co-Cr-W Steel ball | Co-Cr-W鋼球Co-Cr-W Steel ball | Co-Cr-W鋼球Co-Cr-W Steel ball | Co-Cr-W鋼球Co-Cr-W Steel ball | Co-Cr-W鋼球Co-Cr-W Steel ball |
閥桿 | 304 | 316 | 316 | 316 | 316 | 316 | 316 | 316 |
支架 | A105 | F22 | WB36 | F91 | F92 | F316 | F316H | F347H |
填料 | 柔性石墨 | 柔性石墨 | 柔性石墨 | 柔性石墨 | 柔性石墨 | 柔性石墨 | 柔性石墨 | 柔性石墨 |
手輪 | 沖壓 | 沖壓 | 沖壓 | 沖壓 | 沖壓 | 沖壓 | 沖壓 | 沖壓 |
溫壓曲線圖
安裝維護說明
1、產品出廠時已經嚴格檢驗，請勿解體，可打光譜，可試
2、閥門盡可能按閥桿垂直水平面安裝，如需其他方法安裝，河說明
3、安裝時應使介質流向與閥體所示箭頭方向一致，切勿裝反
4、次使用時，須全開門，對閥門及管道進行清洗。調整壓板螺母，確保填料處于良好密封狀態
5、運行中，當工況溫度變化較大（如停機維修）時，檢查并旋緊壓板螺母，壓緊填料。以防閥桿處外漏。
Installment and maintenance instruction
1. Our valves have been examined strictly when leaving the plant, please do not disintegrate. You may hit the spectrum and car
on the pressure test
2. Along the valve stem vertical horizontal plane to install the valve as far as possible, if you need other installment, please explain
3. When installing the valve, you should cause the medium to flow consistent with the arrow direction, do not install instead
4. When installing the valve, please open the valve completely, clean the valve and the pipeline. You should tighten the stem nut
This can guarantee the good seal of the padding
5. In the working time, if the situation temperature changes greatly, please check and tighten the clamp nut, compact the padding
thus the outside leakage from the valve stem will be prevented
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
環保在線 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
