當前位置：上海卓定電子科技有限公司>>Others>>Glassman>>Glassman LH系列高壓電源

Glassman LH系列高壓電源

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號LH系列

品牌

廠商性質其他

所在地

在線詢價收藏產品查看聯系電話

聯系方式：查看聯系方式

更新時間：2023-12-09 13:01:32瀏覽次數：176次

聯系我時，請告知來自環保在線

產品分類 品牌分類

  Others

Glassman

全部產品列表

暫無信息

上海卓定電子科技有限公司

經營模式：其他

商鋪產品：8條

所在地區：

詢價 給他留言

產品簡介

LH Series 5 kW Regulated High Voltage DC Power Supplies 1 kV to 100 kV Rack Mount CE Compliant.The L...

詳細介紹

Glassman LH系列高壓電源

LH Series 5 kW Regulated High Voltage DC Power Supplies 1 kV to 100 kV Rack Mount CE Compliant.The LH family of power supplies are sophisticated, 5 kW, high voltage power supplies with low ripple and noise. They are air insulated, fast response units, with tight regulation. ArcQuench and Arc Sense are features that make the LH series Ideal for Dynamic load environments.

The LH Series are fully compliant with the European Harmonized EMI Directive EN50082-2 and with the European Low Voltage (Safety) Directive, 73/23/EEC.

Glassman LH系列高壓電源特點

From 5% to 99% rated voltage. All units operate down to zero output with very slight degradation of performance.
INPUT:
187-264V RMS, 3-phase, 48-63 Hz, 6500 VA maximum at full load. Less than 20 A/per phase. at 208 VAC. A five position rear terminal block with protective cover is provided.
EFFICIENCY:
Typically greater than 85% at full load.
OUTPUT:
Continuous, stable, adjustment from 0 to rated voltage or current by panel mounted 10-turn potentiometers with 0.05% resolution, or by external 0 to 10 V signals is provided. Linearity is < 1% of rated. Voltage Accuracy is 0.5% of setting + 0.2% rated.
STATIC VOLTAGE REGULATION:
Better than ±0.005% for specified line variations and 0.01% for no load to full load variations.
DYNAMIC VOLTAGE REGULATION:
For load transients from 10% to 99% and 99% to 10%, typical deviation is less than 2% of rated output voltage with recovery to within 1% in 500 μs and recovery to within 0.1% in 1 ms.
RIPPLE:
Better than 0.05% RMS of rated voltage at full load.
CURRENT REGULATION:
When in current regulation mode, better than 0.1%, with 8-100kV models better than 0.2%, from short circuit to rated voltage at any load condition. When in current trip mode the HV output will disable and latch off when the load current reaches the programmed current level. Reset is accomplished by either cycling the AC power or HV ON/OFF buttons, or by toggling the HV enable signal. A switch located on the rear panel allows the selection of current limit modes: onstant current, or current trip.
VOLTAGE MONITOR:
0 to +10 V equivalent to 0 to rated voltage.
Accuracy, 0.5% reading + 0.2% rated.
Impedance is 10 K.
CURRENT MONITOR:
0 to +10 V equivalent to 0 to rated current.
Accuracy: 1 kV to 6 kV: 1.5% of setting plus 0.5% of rated output.8 kV to 100 kV: 1% of setting plus 0.2% of rated output. Output impedance is 10K Ohm differentially coupled.