污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
淄博托維真空設備有限公司
ISG、IRG系列立式單級離心泵,是在我公司生產的IS型泵的基礎上結合管道泵的特點,進行優化設計的一種主要作為管道系統增壓的立式離心泵。在各種不同的使用場合*可以替代IL、IS型泵,適合于工業和城市給排水,高樓建筑水塔增壓供水,消防增壓,管道增壓,遠距離送水,采暖制冷循環供水等場合。鑒于該系列泵的水力模型全部采用IS泵的水力模型,因此保持了IS型泵的高效節能特點,加之采用泵與電機彈性連接,立式安......
ISG、IRG系列立式單級離心泵
ISG、IRG系列立式單級離心泵,是在我公司生產的IS型泵的基礎上結合管道泵的特點,進行優化設計的一種主要作為管道系統增壓的立式離心泵。在各種不同的使用場合*可以替代IL、IS型泵,適合于工業和城市給排水,高樓建筑水塔增壓供水,消防增壓,管道增壓,遠距離送水,采暖制冷循環供水等場合。鑒于該系列泵的水力模型全部采用IS泵的水力模型,因此保持了IS型泵的高效節能特點,加之采用泵與電機彈性連接,立式安裝,密封采用機械密封,支撐選用*的減震裝置,因此該泵具有運行平穩、可靠、噪音低、使用范圍廣等特點,是一種理想的單級單吸離心式管道循環增壓泵。
產品特點:
A 實用性強、性能參數范圍廣
該系列泵性能參數采用ISO2858國際標準,流量范圍1.5~1600m3/h,揚程8~125m氣蝕余量2.5~7m,每一種型號泵通常分為Z、O、A、B、C五個型式,共有291個規格。
B 安裝方便
泵的進出口直徑相同,并且其中心線在同一直線上,能像閥門一樣安裝在管道的任何位置及任意方向,另外泵還設有安裝底腳,極大地方便了泵的安裝和穩固。
C 振動小、噪音低
泵與普通V1型電機彈性連接,避免了直接泵由于連接誤差及懸臂軸過長造成的振動和噪音;葉輪經過嚴格的靜平衡,確保水泵在高速運行時平穩可靠;加之采用低噪音滑動軸承支撐,因此設備運行效果好、噪音低、振動小。
D節約資金
由于其的安裝結構,大大縮小了占地面積和空間,縮小了泵房面積,為用戶節約資金。采用V1電機,可以在戶外使用。
E密封可靠
軸封采用優質可靠的高壓機械密封,確保其不泄漏。也可根據用戶要求,采用填料密封。
F效率高
該系列泵的性能曲線無駝峰,吸入室采用螺旋形吸入室,使液體流動更符合流體力學原理,比直接泵(采用環形吸入室)噪音低,效率高2%~5%。可根據用戶要求,采用串聯或并聯方式運行使用。
G使用壽命長
高效率、低噪音、振動小確保設備使用壽命長。
工作條件:
本系列泵工作壓力1.6MPa,即出口壓力=泵進口壓力+泵揚程<1.6 MPa,泵體靜壓試驗為2.4 MPa,如果泵系統壓力超過下1.6MPa,請在訂貨時說明。本系列泵可輸送溫度不高于80℃的清水或物理化學性質類似于水的其它液體。在泵蓋上增加冷卻系統,可輸送85℃~130℃的上述介質,如輸送介質含有微小顆粒,請在訂貨時說明。
泵的型號組成及意義:
如:ISG80-250(J)Z,O,A,B,C ISG—單級立式離心泵 Z—葉輪直徑加大型 80—泵進/出口直徑(mm) O—葉輪原型 250—葉輪名義直徑 A—葉輪直徑次切割 J—設計轉速為2900r/min的泵 B—葉輪直徑第二次切割降速至1450r/min運轉 C—葉輪直徑第三次切割
型號 | 葉輪形式 | 流量 m 3 /h | 揚程 m | 效率 % | 功率 KW | 必需氣蝕余量 | 轉速 | ||||
|
|
|
|
| 軸功率 | 電機功率 | m | r/min | |||
40-100 | O | 5.04 6.30 7.56 | 15.2 12 10 | 46 50 53 | 0.39 0.41 0.43 | 0.75 | 2.0 2.0 2.5 | 2900 | |||
| A | 4.50 5.60 6.66 | 12.8 10 8 | 45 48 49 | 0.30 0.32 0.35 | 0.75 | 2.0 2.0 2.5 | 2900 |
| A | 4.50 5.60 6.66 | 12.8 10 8 | 45 48 49 | 0.30 0.32 0.35 | 0.75 | 2.0 2.0 2.5 | 2900 |
|
40-100J | O | 2.52 3.2 3.8 | 3.8 3 2.5 | 42 48 51 | 0.06 0.06 0.05 | 0.55 | 2.0 2.0 2.5 | 1450 |
|
A | 2.25 2.8 3.33 | 3.2 2.5 2 | 40 46 49 | 0.05 0.04 0.04. | 0.55 | 2.0 2.0 2.5 | 1450 |
| |
40-125 | O | 5.04 6.30 7.56 | 23.5 20 18 | 43 46 50 | 0.74 0.75 0.75 | 1.1 | 2.0 2.0 2.5 | 2900 |
|
A | 4.50 5.60 6.66 | 19.5 16 14.4 | 42 44 48 | 0.54 0.56 0.57 | 0.75 | 2.0 2.0 2.5 | 2900 |
| |
40-125J | O | 2.52 3.2 3.8 | 5.88 5 4.5 | 41 44 48 | 0.10 0.10 0.10 | 0.55 | 2.0 2.0 2.5 | 1450 |
|
A | 2.25 2.8 3.33 | 4.9 4 3.6 | 39 42 46 | 0.08 0.07 0.07 | 0.55 | 2.0 2.0 2.5 | 1450 | |
40-160 | O | 5.04 6.30 7.56 | 34.5 32 30 | 41 45 49 | 1.16 1.22 1.26 | 1.5 | 2.0 2.0 2.5 | 2900 |
|
A | 4.5 5.6 6.66 | 30.5 28 26.3 | 40 43 47 | 0.92 0.99 1.02 | 1.1 | 2.0 2.0 2.0 | 2900 |
| |
40-160J | O | 2.52 3.2 3.8 | 8.6 8 7.5 | 39 43 47 | 0.15 0.16 0.17 | 0.55 | 2.0 2.0 2.5 | 1450 |
|
A | 2.25 2.8 3.33 | 7.5 7 6.6 | 37 41 45 | 0.12 0.13 0.13 | 0.55 | 2.0 2.0 2.0 | 1450 |
| |
40-200 | O | 5.04 6.30 7.56 | 55 52.5 48 | 35 38 41 | 2.05 2.26 2.41 | 3 | 2.0 2.0 2.5 | 2900 |
|
A | 4.5 5.6 6.66 | 49 46.5 42 | 34 36 39 | 1.77 1.97 1.95 | 2.2 | 2.0 2.0 2.5 | 2900 |
| |
40-200J | O | 2.52 3.2 3.8 | 13.8 13.1 12 | 34 37 39 | 0.28 0.31 0.32 | 0.55 | 2.0 2.0 2.5 | 1450 |
|
| A | 2.25 2.8 3.33 | 12.2 11.6 10.5 | 33 35 37 | 0.23 0.25 0.26 | 0.55 | 2.0 2.0 2.5 | 1450 |
| ||||
50-125 | O | 7.5 12.5 15.0 | 22.0 20.0 18.5 | 47 60 60 | 0.96 1.13 1.26 | 1.5 | 2.0 2.0 2.0 | 2900 |
| ||||
| A | 7.2 11.9 14.3 | 20.0 18.2 16.8 | 46 58 58 | 0.85 1.02 1.13 | 1.5 | 2.0 2.0 2.25 | 2900 |
| ||||
| B | 6.7 11.2 13.4 | 17.5 15.9 14.7 | 45 56 56 | 0.71 0.86 0.96 | 1.1 | 2.0 2.0 2.25 | 2900 |
| ||||
| C | 6.2 10.4 12.5 | 15.2 13.8 12.8 | 44 54 54 | 5.59 0.72 0.80 | 1.1 | 2.0 2.0 2.0 | 2900 |
| ||||
50-125J | O | 3.8 6.3 7.5 | 5.4 5.0 4.6 | 43 54 55 | 0.13 0.16 0.17 | 0.55 | 2.0 2.0 2.5 | 1450 |
| ||||
| A | 3.6 6.0 7.2 | 4.9 4.6 4.2 | 42 52 53 | 0.11 0.14 0.15 | 0.55 | 2.0 2.0 2.25 | 1450 |
| ||||
| B | 3.4 5.6 6.7 | 4.3 4.0 3.7 | 41 50 51 | 0.10 0.12 0.13 | 0.55 | 2.0 2.0 2.05 | 1450 |
| ||||
| C | 3.1 5.2 6.2 | 3.7 3.5 3.2 | 40 48 49 | 0.08 0.10 0.11 | 0.55 | 2.0 2.0 2.0 | 1450 |
| ||||
50-160 | O | 7.5 12.5 15.0 | 34.3 32 29.6 | 44 54 56 | 1.59 2.02 2.16 | 2.2 | 2.0 2.0 2.5 | 2900 |
| ||||
| A | 6.8 11.4 13.7 | 28.4 26.6 24.6 | 41.5 52.53 | 1.27 1.59 1.73 | 2.2 | 2.0 2.0 2.16 | 2900 |
| ||||
| B | 6.1 10.1 12.2 | 22.5 21.0 19.4 | 39 50 51 | 0.95 1.16 1.26 | 1.5 | 2.0 2.0 2.0 | 2900 | |||||
| C | 5.4 9.0 10.8 | 17.9 16.7 15.4 | 36 45 45.5 | 0.73 0.91 1.0 | 1.1 | 2.0 2.0 2.0 | 2900 | |||||
50-160J | O | 3.8 6.3 7.5 | 8.5 8.0 7.5 | 35 48 49 | 0.25 0.29 0.31 | 0.55 | 2.0 2.0 2.0 | 1450 | |||||
| A | 3.4 5.7 6.8 | 7.1 6.7 6.2 | 34 45.5 46 | 0.19 0.23 0.25 | 0.55 | 2.0 2.0 2.16 | 1450 | |||||
| B | 3.0 5.1 6.1 | 5.6 5.3 4.9 | 32 42 42.5 | 0.15 0.17 0.19 | 0.55 | 2.0 2.0 2.0 | 1450 |
| C | 2.7 4.6 5.4 | 4.4 4.2 3.9 | 30 38 38.5 | 0.11 0.14 0.15 | 0.55 | 2.0 2.0 2.0 | 1450 |
50-200 | O | 7.5 12.5 15.0 | 52.5 50.0 48.0 | 38 48 51 | 2.82 3.54 3.95 | 4 | 2.0 2.0 2.5 | 2900 |
A | 7.3 12.1 14.6 | 49.0 47.0 45.0 | 37.5 47 50 | 2.61 3.30 3.58 | 4 | 2.0 2.0 2.3 | 2900 | |
B | 7.0 11.7 14.0 | 45.3 43.2 41.5 | 37 46.2 49.2 | 2.33 2.96 3.20 | 4 | 2.0 2.0 2.15 | 2900 | |
C | 6.5 10.9 13.0 | 39.6 37.7 36.2 | 36 45.2 48.2 | 1.95 2.47 2.67 | 3 | 2.0 2.0 2.0 | 2900 | |
50-200J | O | 3.8 6.3 7.5 | 13.1 12.5 12 | 33 42 44 | 0.41 0.51 0.56 | 0.75 | 2.0 2.0 2.5 | 1450 |
A | 3.6 6.1 7.3 | 12.31.2004 11.8 11.3 | 32.5 41.5 43.2 | 0.38 0.47 0.52 | 0.55 | 2.0 2.0 2.3 | 1450 | |
B | 3.5 5.9 7.0 | 11.3 10.8 10.4 | 32 40.7 42.5 | 0.34 0.42 0.46 | 0.55 | 2.0 2.0 2.15 | 1450 |
| C | 3.3 5.5 6.5 | 9.9 9.4 9.1 | 31 39.5 41.2 | 0.28 0.36 0.39 | 0.55 | 2.0 2.0 2.0 | 1450 |
50-250 | O | 7.5 12.5 15.0 | 82.0 80.0 78.5 | 28.5 38 41 | 5.87 7.16 7.83 | 11 | 2.0 2.0 2.5 | 2900 |
A | 7.0 11.6 13.9 | 70.6 68.9 67.6 | 28 37.5 40 | 4.78 5.80 6.41 | 7.5 | 2.0 2.0 2.3 | 2900 | |
B | 6.5 10.8 13.0 | 61.2 59.7 58.7 | 27.5 36.3 39 | 3.93 4.84 5.30 | 5.5 | 2.0 2.0 2.0 | 2900 | |
C | 6.0 10.0 12.0 | 52.5 51.2 50.2 | 27 35 37.5 | 3.18 3.98 4.38 | 5.5 | 2.0 2.0 2.0 | 2900 | |
50-250J | O | 3.8 6.3 7.5 | 20.5 20 19.5 | 23 32 35 | 0.91 1.07 1.14 | 1.5 | 2.0 2.0 2.5 | 1450 |
A | 3.5 5.9 7.0 | 17.7 17.2 16.8 | 22.1 31.2 24.2 | 0.76 0.88 0.93 | 1.1 | 2.0 2.0 2.25 | 1450 | |
B | 3.2 5.4 6.5 | 15.3 14.9 14.6 | 21.5 30.5 33.5 | 0.63 0.73 0.77 | 1.1 | 2.0 2.0 2.05 | 1450 |
| C | 3.0 5.0 6.0 | 13.1 12.8 12.5 | 21 29.5 32.5 | 0.51 0.60 0.63 | 0.75 | 2.0 2.0 2.0 | 1450 |
65-125 | O | 15.0 25.0 30.0 | 21.8 20.0 18.5 | 58.0 69.0 68.0 | 1.54 1.97 2.22 | 3 | 2.0 2.5 3.0 | 2900 |
A | 14.1 23.5 28.2 | 19.2 17.6 16.3 | 55 67 66 | 1.33 1.68 1.89 | 2.2 | 2.0 2.3 2.6 | 2900 | |
B | 13.2 21.9 26.3 | 16.8 15.4 14.2 | 50.5 62 61 | 1.19 1.48 1.67 | 2.2 | 2.0 2.3 2.6 | 2900 | |
C | 11.3 18.9 22.6 | 12.4 11.4 10.5 | 43.5 53 52 | 0.88 1.10 1.25 | 1.5 | 2.0 2.15 2.4 | 2900 | |
65-125J | O | 7.5 12.5 15 | 5.4 5.0 4.7 | 53 64 65 | 0.21 0.27 0.30 | 0.55 | 2.0 2.0 2.5 | 1450 |
A | 7.0 11.7 14.1 | 4.7 4.4 4.1 | 50.5 61.5 62 | 0.18 0.23 0.26 | 0.55 | 2.0 2.0 2.3 | 1450 | |
B | 6.6 11.0 13.2 | 4.1 3.8 3.6 | 46.5 57 57.5 | 0.16 0.20 0.23 | 0.55 | 2.0 2.0 2.15 | 1450 |
| C | 5.7 9.4 11.3 | 3.0 2.8 2.7 | 51.5 48 18.5 | 0.11 0.15 0.17 | 0.55 | 2.0 2.0 2.0 | 1450 |
65-160 | O | 15.0 25.0 30.0 | 35.0 32.0 30.0 | 54 65 66 | 2.65 3.35 3.71 | 4 | 2.0 2.0 2.5 | 2900 |
A | 14.1 23.5 28.2 | 30.8 28.2 26.4 | 52.5 63 64 | 2.25 2.86 3.16 | 4 | 2.0 2.0 2.25 | 2900 | |
B | 13.0 21.6 25.9 | 26.1 23.9 22.4 | 49.5 58 49 | 1.86 2.42 2.68 | 3 | 2.0 2.0 2.05 | 2900 | |
C | 12.0 20.1 24.1 | 22.5 20.6 19.3 | 46.8 55 55 | 1.58 2.05 2.30 | 3 | 2.0 2.0 2.0 | 2900 | |
65-160J | O | 7.5 12.5 15 | 8.8 8.0 7.2 | 50 50 60 | 0.36 0.45 0.49 | 0.55 | 2.0 2.0 2.5 | 1450 |
A | 7.0 11.7 14.1 | 7.8 7.0 6.3 | 47 58 58 | 0.32 0.39 0.42 | 0.55 | 2.0 2.0 2.25 | 1450 | |
B | 6.5 10.8 13 | 6.6 6.0 5.4 | 45.5 55 55 | 0.25 0.32 0.35 | 0.55 | 2.0 2.0 2.05 | 1450 |
型號 | 葉輪形式 | 流量 m3/h | 揚程m | 效率% | 功率 KW | 必需氣蝕余量 | 轉速 | |
軸功率 | 電機功率 | m | r/min | |||||
| C | 6.0 10.0 12.0 | 5.7 5.2 4.6 | 43 52 52 | 0.22 0.27 0.29 | 0.55 | 2.0 2.0 2.0 | 1450 |
65-200 | O | 15.0 25.0 30.0 | 53.0 50.0 47.0 | 49 60 61 | 4.42 5.67 6.29 | 7.5 | 2.0 2.0 2.5 | 2900 |
65-200 | O | 15.0 25.0 30.0 | 53.0 50.0 47.0 | 49 60 61 | 4.42 5.67 6.29 | 7.5 | 2.0 2.0 2.5 | 2900 |
A | 14.3 23.8 28.5 | 47.8 45.1 42.4 | 48.7 59.5 60.5 | 3.81 4.91 5.44 | 5.5 | 2.0 2.0 2.3 | 2900 | |
B | 13.5 22.5 27.0 | 42.9 40.5 38.1 | 48.3 59 60 | 3.27 4.21 4.67 | 5.5 | 2.0 2.0 2.1 | 2900 | |
C | 12.8 21.3 25.5 | 38.3 36.1 34.0 | 48 57.5 59 | 2.77 3.64 4.00 | 4 | 2.0 2.0 2.0 | 2900 | |
60-200J | O | 7.5 12.5 15 | 13.2 12.5 11.8 | 43 55 57 | 0.63 0.77 0.85 | 1.1 | 2.0 2.0 2.5 | 1450 |
A | 7.1 11.9 14.3 | 11.9 11.3 10.7 | 43 55 57 | 0.54 0.66 0.73 | 0.75 | 2.0 2.0 2.3 | 1450 | |
B | 6.8 11.3 13.5 | 10.7 10.1 9.6 | 43 55 57 | 0.46 0.56 0.62 | 0.75 | 2.0 2.0 2.1 | 1450 |
| C | 6.4 10.6 12.8 | 9.5 9.0 8.5 | 42 54 57 | 0.39 0.48 0.52 | 0.55 | 2.0 2.0 2.0 | 1450 |
60-250 | O | 15.0 25.0 30.0 | 82 80.0 78 | 37 50 53 | 9.05 10.9 12.0 | 13 | 2.0 2.0 2.5 | 2900 |
| A | 14.1 23.4 28.1 | 72.0 70.2 68.5 | 36.5 49 52.4 | 7.55 9.14 10.0 | 11 | 2.0 2.0 2.3 | 2900 |
| B | 13.1 21.9 26.2 | 62.7 61.1 59.6 | 36 47.6 51 | 6.22 7.64 8.34 | 11 | 2.0 2.0 2.0 | 2900 |
| C | 12.3 20.5 24.6 | 55.0 53.7 52.3 | 35.5 46.3 49.7 | 5.18 6.46 7.04 | 7.5 | 2.0 2.0 2.0 | 2900 |
65-250J | O | 7.5 12.5 15 | 21 20 19.4 | 35 46 48 | 1.23 1.48 1.65 | 2.2 | 2.0 2.0 2.5 | 1450 |
| A | 7.0 11.7 14.1 | 18.4 17.6 17.0 | 35 44.8 47 | 1.01 1.25 1.39 | 1.5 | 2.0 2.0 2.26 | 1450 |
| B | 6.6 10.9 13.1 | 16.0 15.3 14.8 | 34.8 43.8 46.2 | 0.82 1.04 1.15 | 1.5 | 2.0 2.0 2.07 | 1450 |
| C | 6.1 10.2 12.3 | 14.1 13.4 13.0 | 34.5 43 45 | 0.68 0.87 0.97 | 1.1 | 2.0 2.0 2.0 | 1450 |
65-315 | O | 15 25 30 | 127 125 123 | 28 50 44 | 18.5 21.3 22.8 | 25 | 2.5 2.5 3.0 | 2900 |
| A | 14 23.3 28.0 | 111 109 107 | 28 39.5 43.5 | 15 17.5 18.5 | 18.5 | 2.5 2.5 2.75 | 2900 |
| B | 13.1 21.9 26.3 | 97.5 96.0 .94.4 | 28 39 43 | 12.5 14.7 15.7 | 17 | 2.5 5.2 2.56 | 2900 |
65-315J | O | 7.5 12.5 15 | 32.3 32 31.7 | 25 37 41 | 2.63 2.94 3.16 | 4 | 2.5 2.5 3.0 | 1450 |
A | 7.0 11.7 14.0 | 28.1 27.9 27.6 | 25 36.6 40.8 | 2.15 2.42 2.58 | 3 | 2.5 2.5 2.75 | 1450 | |
B | 6.6 11.0 13.1 | 24.8 24.6 24.3 | 25 36.3 40.6 | 1.78 2.02 2.15 | 2.2 | 2.5 2.5 2.56 | 1450 | |
| C | 6.1 10.1 12.1 | 21.2 21.0 20.8 | 25 36 40.4 | 1.14 1.61 1.70 | 2.2 | 2.5 2.5 2.5 | 1450 |
80-125 | O | 30 50 60 | 22.5 20 18 | 64 75 74 | 2.87 3.63 3.93 | 4 | 3.0 3.0 3.5 | 2900 |
A | 28.7 47.9 57.4 | 20.6 18.3 16.5 | 63 73 72.5 | 2.56 3.27 3.56 | 4 | 3.0 3.0 3.3 | 2900 | |
B | 26.1 43.6 52.3 | 17.1 15.2 13.7 | 60.45 69.5 68.5 | 2.01 2.59 2.84 | 3 | 3.0 3.0 3.1 | 2900 | |
C | 23.1 38.6 46.3 | 13.4 11.9 10.7 | 58 65.5 64.5 | 1.45 1.91 2.09 | 2.2 | 3.0 3.0 3.0 | 2900 | |
80-125J | O | 15 25 30 | 5.6 5.0 4.5 | 55 71 72 | 0.42 0.48 1.51 | 0.55 | 2.5 2.5 3.0 | 1450 |
A | 14.4 23.9 28.7 | 5.1 4.6 4.1 | 54.5 70 71 | 0.37 0.43 0.45 | 0.55 | 2.5 2.5 2.8 | 1450 | |
B | 13.1 21.8 26.1 | 4.3 3.8 3.4 | 53 66 67 | 0.29 0.34 0.36 | 0.55 | 2.5 2.5 2.55 | 1450 |
型號 | 葉輪形式 | 流量 m3/h | 揚程m | 效率% | 功率 KW | 必需氣蝕余量 | 轉速 | |
軸功率 | 電機功率 | m | r/min | |||||
| C | 11.6 19.3 23.1 | 3.3 3.0 2.7 | 51 62 63 | 0.21 0.25 0.27 | 0.55 | 2.5 2.5 2.5 | 1450 |
80-160 | O | 30 50 60 | 36 32 29 | 61 73 72 | 4.82 5.97 6.57 | 7.5 | 2.5 2.5 3.0 | 2900 |
A | 28.2 46.9 56.3 | 31.7 28.2 25.5 | 60 71 70 | 4.05 5.07 5.59 | 7.5 | 2.5 2.5 2.8 | 2900 | |
B | 25.9 43.2 51.9 | 26.9 23.9 21.7 | 59 67 66 | 3.21 4.2 4.63 | 5.5 | 2.5 2.5 2.6 | 2900 | |
C | 24.1 40.1 48.2 | 23.2 20.6 18.7 | 57 64 63 | 2.67 3.52 3.89 | 4 | 2.5 2.5 2.5 | 2900 | |
80-160J | O | 15 25 30 | 9 8 7.2 | 55 69 68 | 0.67 0.79 0.86 | 1.1 | 2.5 2.5 3.0 | 1450 |
A | 14.1 23.5 28.2 | 7.9 7.0 6.3 | 53.5 66.5 65.5 | 0.57 0.68 0.74 | 0.75 | 2.5 2.5 2.8 | 1450 | |
B | 13.0 21.6 25.9 | 6.7 6.0 5.4 | 51 63 62 | 0.47 0.56 0.61 | 0.75 | 2.5 2.5 2.6 | 1450 | |
| C | 12.0 20.1 24.1 | 5.8 5.2 4.6 | 48 60 59 | 0.4 0.47 0.52 | 0.55 | 2.5 2.5 2.5 | 1450 |
80-200 | O | 30 50 60 | 53 50 47 | 55 69 71 | 7.87 9.87 10.8 | 11 | 2.5 2.5 3.0 | 2900 |
A | 28.0 46.9 55.9 | 46.0 43.4 40.8 | 54.5 67 69.5 | 6.42 8.21 8.93 | 11 | 2.5 2.5 2.7 | 2900 |
80-200J | O | 15 25 30 | 13.2 12.5 11.8 | 51 65 67 | 1.06 1.31 1.44 | 1.5 | 2.5 2.5 3.0 | 1450 |
| A | 14.0 23.3 27.9 | 11.5 10.9 10.2 | 50.6 63 65 | 0.86 1.09 1.20 | 1.5 | 2.5 2.5 2.7 | 1450 |
| B | 12.8 21.3 25.6 | 9.6 9.1 8.6 | 49.4 61.5 62.5 | 0.58 0.85 0.96 | 1.1 | 2.5 2.5 2.53 | 1450 |
| C | 11.8 19.6 23.5 | 8.1 7.7 7.3 | 48 60.5 61.5 | 0.54 0.68 0.75 | 1.1 | 2.5 2.5 2.5 | 1450 |
80-250 | O | 30 50 60 | 84 80 75 | 52 63 64 | 13.2 17.3 19.2 | 22 | 2.5 2.5 3.0 | 2900 |
| A | 28.3 47.2 56.6 | 74.9 71.3 66.8 | 52.3 62.6 64 | 11 14.6 16.1 | 18.5 | 2.5 2.5 2.8 | 2900 |
| B | 26.6 44.4 53.3 | 66.2 63.1 59.1 | 52.5 62.2 64 | 9.1 12.3 13.4 | 15 | 2.5 2.5 2.6 | 2900 |
| C | 23.8 39.6 47.5 | 52.7 50.2 47.0 | 53 60.8 63.5 | 6.43 8.9 9.59 | 11 | 2.5 2.5 2.5 | 2900 |
80-250J | O | 15 25 30 | 21 20 18.8 | 49 60 61 | 1.75 2.27 2.52 | 3 | 2.5 2.5 3.0 | 1450 |
| A | 14.2 23.6 28.3 | 18.7 17.8 16.8 | 49 58.7 59.7 | 1.47 1.95 2.16 | 2.2 | 2.5 2.5 2.8 | 1450 |
| C | 11.9 19.8 23.8 | 13.2 12.6 11.8 | 49 57 59 | 0.87 1.19 1.29 | 1.5 | 2.5 2.5 2.5 | 1450 |
80-315 | O | 30 50 60 | 128 125 123 | 41 54 57 | 25.5 31.5 35.5 | 37 | 2.5 2.5 3.0 | 2900 |
A | 28.0 46.7 56.0 | 112 109 107 | 41 53.5 56.7 | 20.7 25.9 28.8 | 30 | 2.5 2.5 2.7 | 2900 | |
B | 26.3 43.8 52.6 | 98.3 96.0 94.4 | 41 53 56 | 17.2 21.6 24.0 | 30 | 2.5 2.5 2.6 | 2900 | |
C | 24.3 40.5 48.6 | 83.9 81.9 80.6 | 41 52.5 56 | 13.5 17.2 19 | 22 | 2.5 2.5 2.5 | 2900 | |
80-315J | O | 15 25 30 | 32.5 32 31.5 | 39 52 56 | 3.4 4.19 4.6 | 5.5 | 2.5 2.5 3.0 | 1450 |
A | 14.0 23.3 28.0 | 28.3 27.9 27.4 | 39 51.7 55.8 | 2.77 3.43 3.75 | 4 | 2.5 2.5 2.7 | 1450 | |
B | 13.1 21.9 26.3 | 25 24.6 24.2 | 39 51.4 55.6 | 2.29 2.85 3.11 | 4 | 2.5 2.5 2.63 | 1450 |
型號 | 葉輪形式 | 流量 m3/h | 揚程m | 效率% | 功率 KW | 必需氣蝕余量 | 轉速 | |
軸功率 | 電機功率 | m | r/min | |||||
| C | 12.1 20.2 24.3 | 21.3 21.0 20.6 | 39 51.1 55.4 | 1.81 2.26 2.46 | 3 | 2.5 2.5 2.5 | 1450 |
100-125 | O | 60 100 120 | 24 20 16.5 | 67 78 74 | 5.86 7.0 7.28 | 7.5 | 4.0 4.5 5.0 | 2900 |
A | 56.6 94.2 113 | 21.3 17.8 14.7 | 63.5 73 70 | 5.17 6.25 6.45 | 7.5 | 4.0 4.4 4.8 | 2900 | |
B | 53.5 89.2 107 | 19.1 15.9 13.1 | 60 70 65 | 4.64 5.52 5.89 | 7.5 | 4.0 4.2 4.4 | 2900 | |
C | 47.9 79.12 95.0 | 15.0 12.5 10.3 | 54.5 64 62.5 | 3.57 4.22 4.28 | 5.5 | 4.0 4.2 4.4 | 2900 | |
100-125J | O | , 30 50 60 | 6 5 4 | 64 75 71 | 0.77 0.91 0.92 | 1.1 | 2.5 2.5 3.0 | 1450 |
A | 28.3 47.1 56.6 | 5.3 4.4 3.6 | 61 72 66 | 0.67 0.79 0.83 | 1.1 | 2.5 2.5 2.8 | 1450 |
| B | 26.8 44.6 53.5 | 4.8 4.0 3.2 | 57 66 64 | 0.61 0.73 0.73 | 0.75 | 2.5 2.5 2.6 | 1450 |
| C | 23.7 39.6 47.5 | 3.8 3.1 2.5 | 48 61 59 | 0.51 0.55 0.55 | 0.55 | 2.5 2.5 2.5 | 1450 |
100-160 | O | 60 100 120 | 36 32 28 | 70 78 75 | 8.4 11.1 12.2 | 15 | 3.5 4.0 5.0 | 2900 |
A | 56.9 94.8 114 | 32.4 28.8 25.2 | 69.7 77.5 74.2 | 7.2 9.6 10.5 | 11 | 3.5 3.9 4.5 | 2900 | |
B | 53.4 89.0 107 | 28.5 25.4 22.2 | 69 77 74 | 6 8 8.8 | 11 | 3.5 3.8 4.1 | 2900 | |
C | 50.6 84.4 101 | 25.6 22.8 19.9 | 69 76 74 | 5.1 6.9 7.5 | 7.5 | 3.5 3.6 3.9 | 2900 | |
100-160J | O | 30 50 60 | 9.2 8.0 6.8 | 67 75 71 | 1.12 1.45 1.57 | 2.2 | 2.5 2.5 3.5 | 1450 |
A | 28.4 47.4 56.9 | 8.3 7.2 6.1 | 67 76 70 | 0.963 1.22 1.35 | 1.5 | 2.5 2.34 2.9 | 1450 | |
B | 26.7 44.5 53.4 | 7.3 6.3 5.4 | 66 73.3 69 | 0.8 1.05 1.14 | 1.5 | 2.0 2.25 2.6 | 1450 | |
| C | 25.3 42.2 50.6 | 6.6 5.7 4.8 | 65.5 73 68.5 | 0.68 0.90 0.97 | 1.1 | 2.0 2.17 2.4 | 1450 |
100-200 | O | 60 100 120 | 54 50 47 | 65 76 77 | 13.6 17.9 19.9 | 22 | 3.0 3.6 4.8 | 2900 |
A | 56.4 94.1 113 | 47.8 44.2 41.6 | 65 76.5 77 | 11.3 14.8 16.6 | 18.5 | 3.0 3.5 4.3 | 2900 |
| B | 53.5 89.1 107 | 42.9 39.7 37.3 | 65 74.5 76 | 9.6 12.9 14.3 | 15 | 3.0 3.4 3.6 | 2900 |
C | 50.5 84.2 101 | 38.3 35.4 33.3 | 65 73 75 | 8.09 11.1 12.2 | 15 | 3.0 3.2 3.6 | 2900 | |
100-200J | O | 30 50 60 | 13.5 12.5 11.8 | 60 73 74 | 1.84 2.33 2.61 | 3 | 2.0 2.0 2.5 | 1450 |
A | 28.2 47 56.4 | 11.9 11.1 10.4 | 60 72.7 73.7 | 1.53 1.95 2.18 | 2.2 | 2.0 2.0 2.29 | 1450 | |
B | 26.7 44.6 53.5 | 10.7 9.9 9.4 | 60 72.3 73.3 | 1.30 1.67 1.86 | 2.2 | 2.0 2.0 2.15 | 1450 | |
| C | 25.3 42.1 50.5 | 9.6 8.9 8.4 | 60 72 73 | 1.10 1.41 1.57 | 2.2 | 2.0 2.0 2.0 | 1450 |
100-250 | O | 60 100 120 | 87 80 74.5 | 61 72 73 | 23.4 30.3 33.3 | 37 | 3.5 3.8 4.8 | 2900 |
A | 56.0 93.3 112 | 75.8 69.7 64.9 | 59.5 70 70.5 | 19.4 25.6 28.1 | 30 | 3.5 3.6 4.0 | 2900 | |
B | 52.2 87.1 104 | 65.9 60.6 56.5 | 56.5 66 67 | 16.6 21.8 24.0 | 30 | 3.5 3.6 4.0 | 2900 | |
C | 48.5 80.8 96.6 | 56.8 52.2 48.6 | 53 63 67 | 14.1 18.3 20.1 | 22 | 3.5 3.5 3.8 | 2900 | |
100-250J | O | 30 50 60 | 21.3 20 19 | 55 58 70 | 3.16 4.00 4.44 | 5.5 | 2.0 2.0 2.25 | 1450 |
A | 28.0 46.7 56.0 | 18.6 17.4 16.6 | 53 65.5 67.8 | 2.67 3.38 3.72 | 4 | 2.0 2.0 2.25 | 1450 |
| B | 26.1 43.5 52.2 | 16.1 15.2 14.4 | 51 62 64.6 | 2.25 2.90 3.17 | 4 | 2.0 2.0 2.25 | 1450 |
型號 | 葉輪形式 | 流量 m3/h | 揚程m | 效率% | 功率 KW | 必需氣蝕余量 | 轉速 | |
軸功率 | 電機功率 | m | r/min | |||||
| B | 41.6 69.3 83.1 | 16.3 15 13.7 | 60 72 69 | 3.08 3.93 4.49 | 5.5 | 2.2 | 1450 |
125-315 ( Ⅰ ) | Z | 100 167 200 | 145 136 129 | 58 73 73 | 68 84.7 96.7 | 110 | 4.5 | 2900 |
O | 96 160 192 | 133 125 119 | 58 73 73 | 60.0 74.6 85.2 | 90 | 4.5 | 2900 | |
A | 91.7 153 183 | 121 114 109 | 57 72 72 | 53.1 65.9 75.3 | 75 | 4.5 | 2900 | |
B | 87.0 145 174 | 110 103 98.1 | 56 71 71 | 46.4 57.4 65.6 | 75 | 4.5 | 2900 | |
C | 82.4 137 165 | 97.9 92 87.6 | 55 70 70 | 39.9 49.1 56.1 | 75 | 4.5 | 2900 | |
125-315 ( Ⅰ )J | Z | 49.5 82.5 99 | 35.6 34 31.9 | 55 70 70 | 8.72 10.9 12.3 | 15 | 2.1 | 2900 |
O | 48 80 96 | 33.5 32 30 | 55 70 701 | 7.96 9.96 11.2 | 15 | 2.1 | 2900 | |
| A | 45.3 75.5 90.6 | 29.8 28.5 26.7 | 54 69 69 | 6.68 8.49 9.55 | 11 | 2.1 | 1450 |
| B | 43.1 71.8 86.1 | 27 25.8 24.1 | 53 68 68 | 5.97 7.40 8.33 | 11 | 2.1 | 1450 |
| C | 40.7 67.8 81.4 | 24.1 23 21.6 | 52 67 67 | 5.13 6.34 7.13 | 7.5 | 2.1 | 1450 |
125-200 ( Ⅱ ) | O | 120 200 240 | 57.5 50 44.5 | 67 81 80 | 28.0 33.6 36.4 | 37 | 4.5 4.5 5.0 | 2900 |
A | 11 185 222 | 49.3 42.9 38.2 | 64.5 78 77 | 23.1 27.7 30.0 | 30 | 4.5 4.5 4.7 | 2900 | |
B | 103 172 207 | 42.6 37.1 33.0 | 62.5 75 74 | 19.2 23.2 25.1 | 30 | 4.5 4.5 4.5 | 2900 | |
C | 94.4 157 189 | 35.8 31.0 27.9 | 60 71 70 | 15.3 18.7 20.3 | 22 | 4.5 4.5 4.5 | 2900 | |
125-200 ( Ⅱ )J | O | 60 100 120 | 14.5 12.5 11 | 62 76 75 | 3.83 4.48 4.79 | 5.5 | 2.5 2.5 2.75 | 1450 |
| A | 55.6 92.6 111 | 12.4 10.7 9.4 | 61 73.5 73 | 3.08 3.68 3.91 | 4 | 2.5 2.5 2.75 | 1450 |
| B | 51.7 86.1 103 | 10.8 9.3 8.2 | 58 70 69 | 2.61 3.11 3.33 | 4 | 2.5 2.5 2.55 | 1450 |
| C | 47.2 78.7 94.4 | 9.0 7.7 6.8 | 55 66 66 | 2.10 2.51 2.66 | 3 | 2.5 2.5 2.5 | 1450 |
125-250 ( Ⅱ ) | O | 120 200 240 | 87 80 72 | 66 78 75 | 43 55.9 62.8 | 75 | 3.8 4.2 5.0 | 2900 |
A | 112 187 224 | 75.8 69.7 62.7 | 66 78.2 73.5 | 35.0 45.3 52.1 | 55 | 3.8 4.0 4.6 | 2900 | |
B | 104 174 209 | 65.6 60.6 54.6 | 66 78 73 | 28.4 36.9 42.5 | 45 | 3.8 4.0 4.4 | 2900 |
| C | 96.9 162 194 | 56.8 52.2 47 | 66 77.8 73 | 22.7 29.5 34.0 | 37 | 3.8 3.9 4.2 | 2900 |
125-250 ( Ⅱ )J | O | 60 100 120 | 21.5 20 18.5 | 63 76 77 | 5.59 7.17 7.84 | 11 | 2.5 2.5 3.0 | 1450 |
| A | 56 93.3 112 | 18.7 17.4 16.1 | 63 76 77 | 4.53 5.83 6.38 | 7.5 | 2.5 2.5 2.7 | 1450 |
| B | 52.2 87.1 104 | 16.3 15.2 14 | 63 75.5 76.8 | 3.68 4.76 5.19 | 5.5 | 2.5 2.5 2.53 | 1450 |
| C | 48.5 80.8 96.9 | 14 13.1 12.1 | 63 75.2 76.5 | 2.94 3.82 4.17 | 5.5 | 2.5 2.5 2.5 | 1450 |
125-315 ( Ⅱ ) | O | 120 200 240 | 133 125 120 | 60 75 77 | 72.12 90.8 102 | 110 | 5.0 4.5 5.0 | 2900 |
A | 112 187 225 | 116 110 105 | 59 73.5 75 | 60.4 76.4 85.9 | 90 | 4.9 4.7 4.4 | 2900 | |
B | 104 174 209 | 100 94.8 91.0 | 58 70.8 73.1 | 49.3 63.5 70.8 | 75 | 4.3 4.5 4.0 | 2900 | |
C | 96.5 161 193 | 85.7 80.9 77.7 | 57 68.4 71.3 | 39.5 51.8 57.3 | 75 | 4.0 4.2 4.4 | 2900 | |
125-315 ( Ⅱ )J | O | 60 100 120 | 33.5 32 30.5 | 58 73 74 | 9.4 11.9 13.5 | 15 | 2.5 2.5 3.0 | 1450 |
型號 | 葉輪形式 | 流量 m3/h | 揚程m | 效率% | 功率 KW | 必需氣蝕余量 | 轉速 | |
軸功率 | 電機功率 | m | r/min | |||||
| A | 56.2 93.7 112 | 29.4 28.1 26.8 | 56 71.5 72.5 | 8.04 10.0 11.3 | 15 | 2.5 2.5 2.8 | 1450 |
| B | 52.2 87.1 104 | 25.4 24.3 23.1 | 54 69.5 70.5 | 6.69 5.58 9.33 | 11 | 2.5 2.5 2.6 | 1450 |
| C | 48.3 80.4 96.5 | 21.7 20.7 19.7 | 53 67 68 | 5.38 6.77 7.63 | 11 | 2.5 2.5 2.5 | 1450 |
125-400 ( Ⅰ ) | O | 52.6 87.6 105 | 63.6 60 55.2 | 51 63 63 | 17.5 22.7 25 | 30 | 2. | 1450 |
A | 48 80 96 | 53 50 46 | 51 63 63 | 13.6 17.3 19.1 | 22 | 2.0 | 1450 | |
B | 45.0 75.1 90.1 | 46.6 44 40.5 | 50 62 62 | 11.4 14.5 16.0 | 18.5 | 2.0 | 1450 | |
C | 41.9 69.7 83.7 | 40.3 38 35 | 49 61 61 | 9.4 11.8 13 | 15 | 2.0 | 1450 |
125-400 ( Ⅱ ) | O | 60 100 120 | 52 50 48.5 | 53 65 67 | 16.1 21 23.6 | 30 | 2.5 2.5 3.0 | 1450 |
| A | 56.4 93.9 113 | 45.9 44.1 42.8 | 53 65 66.8 | 13.3 17.4 19.7 | 22 | 2.5 2.5 2.75 | 1450 |
| B | 52.3 87.1 105 | 39.4 37.9 36.8 | 53 64.7 66.5 | 10.6 13.9 15.7 | 18.5 | 2.5 2.5 2.6 | 1450 |
| C | 48.8 81 97.2 | 34.1 32.8 31.8 | 53 64.4 66.2 | 8.5 11.2 12.7 | 15 | 2.5 2.5 2.5 | 1450 |
150-250 | O | 120 200 240 | 23.2 20 17.0 | 71 81 78 | 10.7 13.5 14.3 | 15 | 3.0 3.0 3.5 | 1450 |
| A | 112 187 224 | 20.2 17.4 14.8 | 68.5 77 75 | 9.0 11.5 12.0 | 15 | 3.0 3.0 3.5 | 1450 |
| B | 103 171 205 | 16.9 14.6 12.4 | 64.5 75 71 | 7.3 9.1 9.8 | 11 | 3.0 3.0 3.0 | 1450 |
| C | 95.4 159 191 | 14.7 12.6 10.7 | 61.5 71 68 | 6.2 7.7 8.2 | 11 | 3.0 3.0 3.0 | 1450 |
150-315 | O | 120 200 240 | 34 32 29 | 70 79 80 | 15.9 22.1 23.7 | 30 | 2.5 2.5 3.0 | 1450 |
| A | 112 186 224 | 29.6 27.8 25.2 | 69 78.7 79 | 13.0 18.0 19.4 | 22 | 2.5 2.5 2.7 | 1450 |
| B | 104 174 208 | 25.6 24.1 21.8 | 68 77.7 78 | 10.7 14.7 15.9 | 18.5 | 2.5 2.5 2.5 | 1450 |
| C | 96.4 161 193 | 21.7 20.6 18.7 | 77 76.7 77.2 | 8.6 11.8 12.7 | 15 | 2.5 2.5 2.5 | 1450 |
150-400 | O | 120 200 240 | 53 50 46 | 62 75 74 | 27.9 36.6 40.6 | 45 | 2.0 2.8 3.5 | 1450 |
A | 112 186 224 | 46.1 43.5 40.1 | 62 74.5 73 | 22.6 29.4 32.9 | 37 | 2.0 2.6 3.2 | 1450 | |
B | 105 174 209 | 40.3 38 35 | 62 74 72.4 | 18.5 22.4 27.5 | 30 | 2.0 2.5 3.0 | 1450 | |
C | 96.5 161 193 | 34.3 32.3 29.7 | 62 72.8 71.4 | 14.5 19.4 21.9 | 22 | 2.0 2.4 2.7 | 1450 | |
200-250 | O | 240 400 460 | 25 22 20 | 69 82.5 82 | 23.7 29.1 30.5 | 37 | 3.0 3.5 4.0 | 1450 |
| A | 223 371 427 | 21.5 18.9 17.2 | 67 80 79.5 | 19.5 23.9 .25.2 | 30 | 3.0 3.4 3.7 | 1450 |
| B | 207 345 397 | 18.6 16.4 14.9 | 65.4 77.5 77 | 16.0 19.8 20.9 | 22 | 3.0 3.3 3.5 | 1450 |
| C | 190 317 365 | 15.7 13.8 12.6 | 64.4 74 73.5 | 12.7 16.2 17.0 | 18.5 | 3.0 3.2 3.4 | 1450 |
200-315 | O | 240 400 460 | 37 32 28.5 | 70 82 80 | 34.6 42.5 44.5 | 45 | 3.0 3.5 4.0 | 1450 |
A | 219 369 420 | 30.9 26.7 23.8 | 68 76.2 75 | 27.2 35.0 36.4 | 37 | 3.0 3.4 3.6 | 1450 | |
B | 198 330 380 | 25.2 21.8 19.4 | 61.5 69.33 69 | 22.1 28.3 29.1 | 30 | 3.0 3.2 3.4 | 1450 | |
C | 182 303 348 | 21.2 18.3 16.3 | 58 64 62 | 18.1 23.6 24.9 | 30 | 3.0 3.1 3.3 | 1450 |
200-400 | O | 240 400 460 | 55 50 45 | 74 81 76 | 48.6 67.2 74.2 | 75 | 3.0 3.8 4.5 | 1450 |
型號 | 葉輪形式 | 流量 m3/h | 揚程m | 效率% | 功率 KW | 必需氣蝕余量 | 轉速 | |
軸功率 | 電機功率 | m | r/min | |||||
| A | 224 373 429 | 47.7 43.4 39.1 | 73 79.8 73.5 | 39.8 55.2 62.0 | 75 | 3.0 3.6 4.1 | 1450 |
| B | 209 348 401 | 41.7 37.9 34.1 | 72 78.6 72 | 33.0 45.8 51.7 | 55 | 3.0 3.4 3.8 | 1450 |
| C | 194 324 373 | 36.1 32.8 29.5 | 71 77 70.5 | 26.9 37.6 42.5 | 45 | 3.0 3.25 3.6 | 1450 |
250-315 | Z | 380 630 760 | 41 38 35 | 71 84.5 84 | 59.7 77.1 86.2 | 90 | 4.8 5.5 7 | 1480 |
O9 | 380 630 760 | 35.5 32 29 | 71 84.5 84 | 51.7 65 71.4 | 75 | 4.8 5.5 7 | 1480 | |
A | 360 590 720 | 31.6 28.5 25.8 | 69.5 83 82.5 | 44.6 55.1 61.3 | 75 | 4.7 5.4 6.9 | 1480 | |
B | 340 560 670 | 27.7 25 22.6 | 68.5 82 81.5 | 37.4 46.5 50.6 | 55 | 4.6 5.3 6.8 | 1480 | |
250-400 | Z | 380 630 760 | 56.3 54.5 51.5 | 71 84.5 82.5 | 82.03 110.6 129.15 | 132 | 4.9 5.5 6.9 | 1480 |
| O | 380 630 760 | 52 50 46.7 | 71 84.5 82.5 | 75.8 101.5 117.1 | 132 | 4.9 5.5 6.9 | 1480 |
| A | 360 600 720 | 46.8 45 42 | 70 83 81 | 65.99 88.6 101.63 | 110 | 4.8 5.4 6.8 | 1480 |
| B | 340 560 680 | 41.6 40 37.4 | 68.5 82 80 | 56.2 74.4 86.5 | 90 | 4.7 5.3 6.7 | 1480 |
| C | 320 530 640 | 36.4 35 32.7 | 67.5 81 79 | 46.9 62.3 72.1 | 75 | 4.5 5.1 6.5 | 1480 |
300-315 | Z | 600 1000 1200 | 43.8 37.5 34 | 72 86 86 | 99.4 119 129 | 132 | 5.3 7.5 8.5 | 1480 |
O | 600 1000 1200 | 38 32 28 | 72 86 85 | 86.2 101.3 107.6 | 110 | 5.3 7.5 8.5 | 1480 | |
A | 570 940 1130 | 33.8 28.5 24.8 | 70.5 84 83.5 | 74.4 86.8 91.4 | 110 | 5.2 7.3 8.4 | 1480 | |
B | 530 880 1060 | 29.7 25 21.9 | 69.5 83 82.5 | 61.7 72.2 76.6 | 90 | 4.9 7.1 8.1 | 1480 |
300-400 | Z | 600 100 1200 | 66.5 65 62 | 73 86 84 | 148.8 206 241.1 | 250 | 5.5 7.5 7.7 | 1480 |
O | 600 1000 1200 | 53.5 50 47.2 | 73 86 84 | 129.8 158.3 170.3 | 200 | 5.5 7.5 7.7 | 1480 | |
A | 570 950 1140 | 48 45 42.5 | 71 84 82 | 104.9 138.5 160.9 | 200 | 5.4 7.3 7.6 | 1480 | |
B | 540 890 1070 | 42.8 40 37.7 | 70.5 83.5 81 | 89.2 116 135.6 | 132 | 5.3 7.1 7.5 | 1480 | |
350-315 | O | 960 1600 1920 | 38.4 32 26.5 | 77 85 52 | 130 164 169 | 200 | 8.1 11 11.2 | 1480 |
A | 910 1510 1810 | 34.2 28.5 23.6 | 75 83 80 | 113 141.2 145.4 | 160 | 9.9 10.8 11.0 | 1480 | |
B | 850 1410 1700 | 30 25 20.5 | 74 81.5 19 | 93.8 118 120 | 132 | 9.6 10.5 11.0 | 1480 | |
350-400 | O | 960 1600 1920 | 56.5 50 44 | 77 87 84 | 191.8 250.3 273.8 | 280 | 8.1 11 11.2 | 1480 |
| A | 910 1520 1820 | 50.8 45 39.5 | 75.5 85.5 82.5 | 166.7 217.8 237.2 | 250 | 9.9 10.8 11.0 | 1480 |
B | 860 1430 1720 | 45.2 40 35.2 | 75 84.5 81.5 | 141.1 184.3 202.2 | 220 | 9.6 10.5 11.0 | 1480 | |
C | 800 1340 1610 | 39.5 35 30.8 | 74 83.5 80.5 | 116.3 153 167.7 | 200 | 9.5 10.4 11.0 | 1480 |
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
環保在線 設計制作,未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
請輸入你感興趣的產品
請簡單描述您的需求
請選擇省份