當前位置：上海巨納科技有限公司>>二維材料>>硒化物晶體>>MoWTe2 二硒化鎢鉬晶體

MoWTe2 二硒化鎢鉬晶體

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號

品牌

廠商性質其他

所在地上海

在線詢價 收藏產品查看聯系電話

聯系方式：袁文軍查看聯系方式

更新時間：2024-02-13 14:26:17瀏覽次數：78次

聯系我時，請告知來自環保在線

產品分類 品牌分類

  二維材料

二維材料粉末

二維材料溶液

碲化物晶體

硒化物晶體

硫化物晶體

絕緣體

鈣鈦礦

異質結

MOFS材料

二維材料薄膜

黑磷

六方氮化硼

其他二維材料

全部產品列表

暫無信息

上海巨納科技有限公司

經營模式：其他

商鋪產品：574條

所在地區：

聯系人：袁文軍

詢價 給他留言

產品簡介

簡要描述：The first MoWTe2 ternary alloy.

詳細介紹

The first MoWTe2 ternary alloy. Large single crystal defect free molybdenum tungsten ditelluride (MoxW(1-x)Te2) crystals have been developed in our facilities and they have x=0.3,0.5, and 0.7 stoichiometric ratios. As they are semiconductor grade (99.9995% purity and perfect stoichiometry), you do not need to worry about amorphous phase, defects, or contamination. As the crystal size is large, they are ideal for exfoliating large monolayers. Single crystal MoWTe2 are very easy to exfoliate and the monolayer yield is high. Our crystals are grown using two different techniques through chemical vapor transport (CVT) or flux zone growth (see description of these two methods below) and their composition values were determined by XPS, SAED, and EDS measurements.. These crystals all possess extremely narrow PL bandwidths, display clean PL spectra, high carrier mobility, extremely clean and sharp XRD peaks, and negligible amount of defects (see published results as well as CVT vs. Flux based methods below ). These crystals come with guaranteed alloying and valleytronic response, sharp PL, and good electronic response.

Important advantages of our crystals

1. Crystals come fully characterized using macro, micro, and nanoscale measurements (see below)
2. Thanks to our improved flux zone growth method, our crystals are homogeneously alloyed which means across the specimen you will only find one particular x composition.
3. No separation: Phase separation is commonly observed in 2D TMDCs alloys when cooling profiles are not controlled carefully. Our R&D team has worked over five (5) years to solely solve this problem.

During order please specify the desired composition ratio.

Growth method matters> Flux zone or CVT growth method? Contamination of halides and point defects in layered crystals are well known cause for their reduced electronic mobility, reduced anisotropic response, poor e-h recombination, low-PL emission, and lower optical absorption. Flux zone technique is a halide free technique used for synthesizing truly semiconductor grade vdW crystals. This method distinguishes itself from chemical vapor transport (CVT) technique in the following regard: CVT is a quick (~2 weeks) growth method but exhibits poor crystalline quality and the defect concentration reaches to 1E11 to 1E12 cm-2 range. In contrast, flux method takes long (~3 months) growth time, but ensures slow crystallization for perfect atomic structuring, and impurity free crystal growth with defect concentration as low as 1E9 - 1E10 cm-2. During check out just state which type of growth process is preferred. Unless otherwise stated, 2Dsemiconductors ships Flux zone crystals as a default choice.