ProLAD CD900R750

TEL：188-24-24-30-80

Q：306-167-1820（詢價請加Q）
Precimeter的智能數字激光和照相機金屬液位傳感器是專門為此目的而開發的高性能激光三角測量設備。它將在表面溫度低于1000?C的任何熔融金屬表面上進行測量。

無需安全措施。
ProLAD CD900R750即使在困難的環境中也能保持穩定的讀數
簡易安裝
設計緊湊
激光等級2批準
Precimeter傳感器中獲得的數碼相機技術，可實現*的靈敏度，穩定性和準確性。這樣就可以使用2類激光器，這意味著不需要采取特殊的安全措施。即使材料的反射率發生巨大變化，以及在煙霧，蒸汽和火的惡劣條件下，也可以提供穩定的讀數。

激光傳感器類型
間隙距離
測量范圍
解析度
CD900R750 900毫米（35.4英寸）750毫米（29.5英寸）+-1毫米（0.04英寸）
光源：激光二極管635 nm（可見紅光）
激光功率：<1 mW，F(xiàn)DA II級
采樣頻率：250 Hz
配置接口：RS232C
模擬輸出：4-20 mA（可選0-10 VDC，0-20 mA）
電源要求：18-32 VDC，<1A
非線性：測量范圍的±0.2％
相對濕度：25-85％（非冷凝）
環保：IP65（NEMA4）

ProZ

• No safety measures required.
• Stable readings even in difficult environments
• Easy installation
• Compact design
• Laser class 2 approved

The patented digital camera technology in the Precimeter sensors, results in very high sensitivity, stability and accuracy. This enables the use of class 2 lasers, which means that no special safety measures are required. It also makes it possible to give stable readings even when the material reflectivity changes dramatically and in harsh conditions with smoke, steam and fire.

• Light source: Laser diode 635 nm (visible red light)
• Laser power: < 1 mW, FDA Class II
• Sampling frequency: 250 Hz
• Configuration interface: RS232C
• Analog output: 4-20 mA (optional 0-10 VDC, 0-20 mA)
• Power requirement: 18-32 VDC, < 1A
• Non-linearity: ±0.2% of Measurement range

ProLAD

The intelligent digital laser and camera metal level sensor from Precimeter is a high performance laser triangulation device developed specifically for its purpose. It will measure on any molten metal surface with a surface temperature below 1000?C.

• No safety measures required.
• Stable readings even in difficult environments
• Easy installation
• Compact design
• Laser class 2 approved

The patented digital camera technology in the Precimeter sensors, results in very high sensitivity, stability and accuracy. This enables the use of class 2 lasers, which means that no special safety measures are required. It also makes it possible to give stable readings even when the material reflectivity changes dramatically and in harsh conditions with smoke, steam and fire.

• Light source: Laser diode 635 nm (visible red light)
• Laser power: < 1 mW, FDA Class II
• Sampling frequency: 250 Hz
• Configuration interface: RS232C
• Analog output: 4-20 mA (optional 0-10 VDC, 0-20 mA)
• Power requirement: 18-32 VDC, < 1A
• Non-linearity: ±0.2% of Measurement range
• Relative humidity: 25-85% (non condensing)
• Environmental protection: IP65 (NEMA4)