進口法蘭高溫電磁閥，High temperature solenoid valve，是指閥體以及密封采用耐高溫的材料，采用耐溫線圈、不易燒毀、精密鑄造、外觀精美的電磁閥，適用于中高溫?zé)崴?dǎo)熱油、高溫蒸汽、飽和蒸汽及過熱蒸汽等管路的自動控制,zui高耐溫達550度；廣泛應用于科研、服裝設備、石油化工、生物制藥、暖通空調、電鍍涂裝、干燥設備、橡塑機械、食品飲料、造紙、印染及電力礦業等行業。
進口法蘭高溫電磁閥產品特點：
進口高溫電磁閥閥芯均為不銹鋼活塞式，活塞環用特殊耐溫、耐磨材料制作；活塞與金屬閥腔不產生直接摩擦，閥體安裝方向無限制；特制線圈，并采用散熱的結構方式，因此不易燒毀；長時間停止動作重新啟動，動作同樣靈敏；zui低啟動壓力0.2MPa。
進口高溫電磁閥原理結構：分步直動導向凹凸型金屬活塞式；一步直動導向凹凸型金屬活塞式,
工作環境溫度：-20-+50℃、-40-+80℃
線圈工作溫度：<+50℃、<+85℃
控制方式：常閉、常開
標準電壓：AC220V、DC24V
流通流體介質：高溫蒸汽、高溫氣、高溫油等
流通流體溫度：<+150℃、<+200℃、<+250℃、<+350℃、<+450℃,<+650℃
密封材質性能：耐高溫、耐壓、耐磨、防腐 
泄漏量：零
密封結構：圓弧錐線與平面密封
性能特點：通用性廣、靈敏性高、嚴密性強、壽命性長
工作范圍：醫療、冶金工業、石油化工、電力設備、干燥設備等  

的使用保養

原文：
高溫電磁閥的使用保養：
1、建議使用單位派專人負責使用保養。 
2、高溫電磁閥安裝后需通入介質實驗動作數次，確認正常后方可投入正式使用。 
3、應定期清洗大閥內外及銜吸合面的污物，注意不要損壞密封面。 
4、高溫電磁閥較長時間不用時，應關閉閥前手動閥，重新啟用時，蒸汽電磁閥應將冷凝水排除干凈，并作試動作數次，待開關正常后方可投入使用。
5、高溫電磁閥從管路上卸下不用時，應將內部及零件拭凈并用壓縮空氣吹凈儲存。 
6、使用時間較長時，如活塞與閥座間密封不好，可將活塞密封面重新磨平，再和閥座研磨。 
7、工作時，要注意閥門前后壓力表，要求工作壓力不得超過額定壓力，工作壓差必須在額定壓差范圍內。當工作壓力超過額定壓力或工作壓差超過額定壓差時，電磁閥要停止使用，關閉前后手動閥，以免電磁閥爆炸和泄漏。

譯文：
High temperature solenoid valves for use and maintenance:
1, recommended by a person responsible for maintenance. 
2, high temperature solenoid valve installed after the required access media test action several times, known until put into formal use. 
3, should regularly clean the valve and the suction surface of dirt in his mouth, careful not to damage the sealing surface. 
4, a long time when you're not using high temperature solenoid valve, close the valve before the valve manually, when you re-enable the steam solenoid valve drain water should be clean, and tried a number of times until the normal rear switch can be put into use. 
5, high temperature solenoid valve from the pipeline to remove when not in use, interior parts and components should be wiping clean with compressed air blowing off store. 
6, used for a long time, such as bad seal between the piston and valve seat, piston sealing surface can be worn again, and seat grinding. 
7, work, should pay attention to before and after the valve pressure gauge required working pressure must not exceed the rated pressure, work pressure must be within the rated pressure range. When the pressure exceeds the rated pressure or when the pressure exceeds the rated pressure differential, solenoid valve to stop using, close the manual valve, so as to avoid explosions and the solenoid valve leaking.
高溫電磁閥的使用保養