污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
北京艾諾德儀器有限公司
低溫彎折儀
【詳細說明】
低溫彎折儀操作規程溫彎折儀根據標準GB12952-91, GB/T16777-1997的要求設計制造,既適合做防水卷材的要求設計制造,
低溫彎折儀 操作規程:
1、按 GB12953—2003 的圖 1 表 4 裁取試件,將試件的迎 水面朝外,彎曲 180 度,使 50mm 寬的邊緣重合;齊平;并固 定。將彎折儀上下平板距離調節為卷材厚度的 3 倍。
2、
北京艾諾德儀器有限公司,致力于打造中國儀器航母品牌。
北京艾諾德儀器有限公司是集專業設計、開發、生產與銷售于一體的*股份制企業,專注于新型材料試驗機的研制、材料檢測技術的提高及材料試驗方法的創新,是國內的材料試驗檢測儀器的生產企業。
低溫彎折儀
編號:GD201311280004
規格:WZY-A
【詳細說明】
低溫彎折儀操作規程溫彎折儀根據標準GB12952-91, GB/T16777-1997的要求設計制造,既適合做防水卷材的要求設計制造,
低溫彎折儀 操作規程:
1、按 GB12953—2003 的圖 1 表 4 裁取試件,將試件的迎 水面朝外,彎曲 180 度,使 50mm 寬的邊緣重合;齊平;并固 定。將彎折儀上下平板距離調節為卷材厚度的 3 倍。
2、儀翻開,把兩塊試件平放在下平板上,重合的一邊朝 向轉軸,且據轉軸 20mm。在設定溫度下將彎折儀與試件一起 放入低溫箱中,達到規定溫度后在此溫度下放置 1h。然后在 標準溫度下將上平板 1s 內壓下,達到所調間距位置,在此位 置保持 1s 后將試件取出。恢復到室溫后觀察彎折處是否斷裂, 或用 6 倍大放大鏡觀察試件彎折處有無裂紋。
高分子防水涂料 將試件在標準條件下放置 2h 后彎曲 180 度,使 25mm 寬 的邊緣對齊,用訂書機將邊緣外固定,調整彎折儀的上平板與 下平板的距離為試件厚度的 3 倍, 然后將試件放在彎折儀的下 平板上,試件重疊的一邊朝向彎折機軸。據轉軸中心約 25mm 的彎折儀放入低溫箱中,再規定溫度下保持 2 后打開低溫箱, 保持 1 出試件并用 8 倍放大鏡觀察試件。 在 1 內將上平板壓下, 四、 記錄試件表面有無裂痕或開裂現象。
Low temperature bending apparatus
Number: GD201311280004
Specification: WZY - A
"Detail"
Low temperature bending machine operation procedures temperature bending apparatus according to the standard GB12952-91, the requirements of GB/T16777-1997 design and manufacturing, is suitable for the requirements of waterproofing design and manufacture,
Low temperature bending apparatus Operating procedures:
1, according to figure 1 GB12953-2003 table 4 cropping specimens, will meet the surface of the specimens, bent 180 degrees, make the edge of the 50 mm wide overlap; Flush; And fixed. The thickness of upper and lower plate distance adjustment for coil bending apparatus three times.
2, open, put the two pieces of flat specimen on a flat, one side of the overlap toward to the rotating shaft, and according to the axis of 20 mm. Will bend under the set temperature meter, together with the specimen in the low temperature box, reach the specified temperature place 1 h at this temperature. Then under the standard temperature will tablet 1 s under internal pressure, achieve the space position, in this place to keep remove specimen after 1 s. After return to room temperature observation inquire whether bending fracture, or with 6 times as big as a magnifying glass to observe specimen bending crack.
Polymer waterproof coating place specimen under standard conditions after 2 h bent 180 degrees, make the 25 mm wide edge alignment, the edge of the external fixation with stapler, adjust the bending device on the tablet and the specimen thickness of the plate distance under the conditions of the three times, then put the specimen on the plate under bending apparatus, one side of the specimen overlap toward bending machine shaft. According to the rotation center of about 25 mm bending apparatus in the low temperature box, again under the specified temperature for 2 after open the cryostat, to keep the specimen with eight times a magnifying glass observation specimen 1. On within 1 tablet press, four, record the specimen surface with and without cracks or cracking phenomenon.
售后服務承諾:
1、服務宗旨:快速、果斷、準確、周到、*
2、服務目標:服務質量贏得用戶滿意
3、服務效率:保修期內或保修期外如設備出現故障,供方在接到通知后,1-3個工作日內予以解決。 用戶可以通過售后咨詢有關技術問題,并得到明確的解決方案
4、服務原則:儀器儀表產品保修期為1年,在保修期內供方將免費維修和更換屬質量原因造成的零部件損壞,保修期外零部件的損壞,提供的配件只收成本費,由需方人為因素 造成的設備損壞,供方維修或提供的配件均按成本價計。
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
商鋪:http://www.kindlingtouch.com/st116882/
主營產品:生產銷售氣體檢測儀,不銹鋼電熱蒸餾水器,甲醛穿孔萃取器,便攜式粉塵儀,粉末取樣器,風速風向儀,真空度檢測儀,酸堿度計,百葉箱
環保在線 設計制作,未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
請輸入你感興趣的產品
請簡單描述您的需求
請選擇省份