東莞液壓系統配套廠家，液壓系統加工設計，金中液壓泵站定做生產廠家
加工定制：是 | 品牌：金中KQK | 型號：非標液壓系統定做設計 |
合用范圍：油壓機、車輛產業、船舶、輪胎機、拉伸機械、壓床機械、橡膠發 | 產品別號：液壓系統液壓站 | 材質：鑄鐵 |
合用介質：液壓油 | 合用溫度：-10-70（℃） | 公稱壓力：31（MPa） |
1低能源：經設計油路，所需能源1切不鋪張。
液壓站的特點
2低噪音：施工細致、品質精確、噪音低。
3機種豐碩：油路多種組合，機種豐碩。
4尺度油路、控制回路、保養維修輕易。
5省空間：泵與電機直接結合，節省空間。
7特殊機種能隨客戶需求調整，接受定制。
1）在管路中裝油濾，以保護閥的供油管路和壓力管路。 液壓系統的維護:
1個系統在正式投入之前1般都要經由沖刷，沖刷的目的就是要清除殘留在系統內的污染物、金屬屑、纖維化合物、鐵心等，在zui初兩小時工作中，即使沒有*損壞系統，也會引起1系列故障。
要是系統中使用到電液伺服閥，我不妨多說兩句，伺服閥得沖刷板要使油液能從供油管路流向集流器，并直接返回油箱，這樣可以讓油液反復暢通流暢，以沖刷系統，讓油濾濾掉固體顆粒，沖刷過程中，沒隔1～2小時要檢查1下油濾，以防油濾被污染物堵塞，此時旁路不要打開，若是發現油濾開始堵塞就馬上換油濾。
2）確保沒有外來顆粒從油箱的通氣蓋、油濾的塞座、回油管路的密封墊圈以及油箱其他啟齒處進入油箱。所以應該按下列步驟來清洗系統油路：
3）用1種易干的清潔溶劑清洗油箱，再用經由過濾的空氣清除溶劑殘渣。 。
4）清洗系統全部管路，某些情況下需要把管路和接頭進行浸漬。
5）修護好系統中的泄漏。
6）檢查液壓油被酸化或其他污染物污染情況，液壓油的氣息可以大致鑒別是否變質。
7）在集流器上裝1塊沖刷板以代替精密閥，如電液伺服閥等。
8）按期沖刷油泵的入口油濾。
沖刷的周期由系統的構造和系統污染程度來決定，若過濾介質的試樣沒有或是很少外來污染物，則裝上新的油濾，卸下沖刷板，裝上閥工作！
有計劃的維護：建立系統按期維護軌制，對液壓系統較好的維護保養建議如下：
9）至多500小時或是3個月就要檢查和更換油液。
10）檢查所有管路尺寸是否合適，連接是否準確。
：400-080-3988
移動13925539480
13925501948
13925580728
：0769-22859339
GW：www.yeyaxt。。ｃｏｍ www.jzyyz。。ｃｏｍ www.pumps88。。ｃｏｍ
Dongguan hydraulic system supporting manufacturers , hydraulic system process design , gold custom manufacturer of hydraulic pump station
Custom processing: Brand: Golden KQK Type: Non-standard hydraulic system custom design
Combined range: hydraulic machines, industrial vehicles , ships, tire machine, stretching machinery, mechanical presses , rubber hair products alias : Hydraulic system Hydraulic station Material: cast iron
Combined medium: hydraulic oil combined temperature : -10-70 （℃） Nominal pressure : 31 （MPa）
1 Low Energy: The perfect design circuit , all the energy required is not extravagant.
Hydraulic characteristics
2 Low noise: construction detail, quality and precision , low noise.
Three models fruitful : many combinations of asphalt models fruitful .
4 scale circuit, control circuit , maintenance easily .
5 Space-saving : pump and motor directly coupled to save space.
7 Special models can be adjusted with customer demand , accept custom .
1 ） are installed in the pipe oil filter to protect the valve supply line and pressure line . Hydraulic system maintenance :
Before a system is put into generally required by erosion, scour aim is to remove residual contaminants in the system , scrap metal , fiber compounds , core , etc., in the first two hours of work , even if not compley damage the system will caused by a series of failures .
If the system using the servo valve , I might say a few words , the servo valve was washed plates make the flow of oil from the current collector supply line and return directly to the tank , so you can make the oil flow smoothly again to flush the system , so that the oil filter to filter out solid particles , erosion process, not every 1 to 2 hours to check the oil filter , oil filter to prevent clogging by contaminants , then do not open the bypass , if discovered oil filter starts immediay clogged oil filter .
2 ） Ensure that no foreign particles from the fuel tank vent cap , oil filter the plug seat, return line gaskets and other ashamed at the tank into the tank . So it should be according to the following steps to clean the system oil :
3 ） with an easy to dry cleaning solvent cleaning tank , and then through the filtered air purge solvent residue. .
4 ） All piping cleaning system , in some cases require the immersion pipes and joints .
5 ） good repair leaks in the system .
6 ） Check the hydraulic oil is acidifying pollution or other contaminants , hydraulic oil flavor can roughly identify whether deterioration.
7 ） attach the collector plate in place of a precise flush valve , such as electro-hydraulic servo valve.
8 ） Regular flushing pump inlet oil filter .
Cycle of erosion by the system's structure and systems to determine the extent of contamination , if the filter media is no or very little external sample contamination , then put on a new oil filter , remove the flush plate , mounted on the valve work !
Planned Maintenance: Regular maintenance rail system create a system , the hydraulic system better maintenance recommendations are as follows :
9 ） up to 500 hours or three months is necessary to check and replacement fluids.
10 ） Check that all piping is the right size , the connection is accurate.
Free hotline :400 -080-3988
phone:
Landline 0769 -22,859,339
GW: www.yeyaxt。。ｃｏｍ www.jzyyz。。ｃｏｍ www.pumps88。。ｃｏｍ
