嘔吐毒素檢測試劑盒規 格:96T
檢測標本:各種動物肌肉組織、肝臟、尿液、血清、水產、蜜蜂、牛奶、糧食作物(玉米、大米、豆類、花生、麥類等)、飼料等
檢測方法:ELISA
檢測類型:酶聯免疫分析法
產品的用途:僅供科研究課題使用
嘔吐毒素檢測試劑盒價格及詳細資料:電議,或咨詢在線客服,或者以郵件形式發到我司qysw@qiyibio.com .齊一生物科技(上海)有限公司提供的ELISA試劑盒受到了廣大科研單位的*肯定和認同。*保證,價格公道,傾力為國內外科研院校實驗室提供的產品。若有需要,我司將竭誠為您服務!
本試劑盒用于測定各種動物肌肉組織、肝臟、尿液、血清、飼料等水產/蜂蜜/牛奶相關液體樣本中殘留的定量檢測。
實驗原理:
本試劑盒應用雙抗體夾心法測定標本中該產品水平。用純化的本產品抗體包被微孔板,制成固相抗體,往包被單抗的微孔中依次加入本產品抗原,再與HRP標記的本產品抗體結合,形成抗體-抗原-酶標抗體復合物,經過*洗滌后加底物TMB顯色。TMB在HRP酶的催化下轉化成藍色,并在酸的作用下轉化成zui終的黃色。顏色的深淺和樣品中的本產品呈正相關。用酶標儀在450nm波長下測定吸光度(OD值),通過標準曲線計算樣品中該產品濃度。
試劑盒組成:
試劑盒組成 | 48孔配置 | 96孔配置 | 保存 |
說明書 | 1份 | 1份 |
|
封板膜 | 2片(48) | 2片(96) |
|
密封袋 | 1個 | 1個 |
|
酶標包被板 | 1×48 | 1×96 | 2-8℃保存 |
標準品:1800ng/L | 0.5ml×1瓶 | 0.5ml×1瓶 | 2-8℃保存 |
標準品稀釋液 | 1.5ml×1瓶 | 1.5ml×1瓶 | 2-8℃保存 |
酶標試劑 | 3 ml×1瓶 | 6 ml×1瓶 | 2-8℃保存 |
樣品稀釋液 | 3 ml×1瓶 | 6 ml×1瓶 | 2-8℃保存 |
顯色劑A液 | 3 ml×1瓶 | 6 ml×1瓶 | 2-8℃保存 |
顯色劑B液 | 3 ml×1瓶 | 6 ml×1瓶 | 2-8℃保存 |
終止液 | 3ml×1瓶 | 6ml×1瓶 | 2-8℃保存 |
濃縮洗滌液 | (20ml×20倍)×1瓶 | (20ml×30倍)×1瓶 | 2-8℃保存 |
標本要求:
1.標本采集后盡早進行提取,提取按相關文獻進行,提取后應盡快進行實驗。若不能馬上進行試驗,可將標本放于-20℃保存,但應避免反復凍融
2.不能檢測含NaN3的樣品,因NaN3抑制辣根過氧化物酶的(HRP)活性。
操作步驟:
- 標準品的稀釋與加樣:在酶標包被板上設標準品孔10孔,在*、第二孔中分別加標準品100μl,然后在*、第二孔中加標準品稀釋液50μl,混勻;然后從*孔、第二孔中各取100μl分別加到第三孔和第四孔,再在第三、第四孔分別加標準品稀釋液50μl,混勻;然后在第三孔和第四孔中先各取50μl棄掉,再各取50μl分別加到第五、第六孔中,再在第五、第六孔中分別加標準品稀釋液50ul,混勻;混勻后從第五、第六孔中各取50μl分別加到第七、第八孔中,再在第七、第八孔中分別加標準品稀釋液50μl,混勻后從第七、第八孔中分別取50μl加到第九、第十孔中,再在第九第十孔分別加標準品稀釋液50μl,混勻后從第九第十孔中各取50μl棄掉。(稀釋后各孔加樣量都為50μl,濃度分別為1200 ng/L,800 ng/L ,400 ng/L,200ng/L, 100 ng/L)。
- 加樣:分別設空白孔(空白對照孔不加樣品及酶標試劑,其余各步操作相同)、待測樣品孔。在酶標包被板上待測樣品孔中先加樣品稀釋液40μl,然后再加待測樣品10μl(樣品zui終稀釋度為5倍)。加樣將樣品加于酶標板孔底部,盡量不觸及孔壁,輕輕晃動混勻。
- 溫育:用封板膜封板后置37℃溫育30分鐘。
- 配液:將30(48T的20倍)倍濃縮洗滌液用蒸餾水30(48T的20倍)倍稀釋后備用。
- 洗滌:小心揭掉封板膜,棄去液體,甩干,每孔加滿洗滌液,靜置30秒后棄去,如此重復5次,拍干。
- 加酶:每孔加入酶標試劑50μl,空白孔除外。
- 溫育:操作同3。
- 洗滌:操作同5。
- 顯色:每孔先加入顯色劑A50μl,再加入顯色劑B50μl,輕輕震蕩混勻,37℃避光顯色15分鐘.
- 終止:每孔加終止液50μl,終止反應(此時藍色立轉黃色)。
- 測定:以空白空調零,450nm波長依序測量各孔的吸光度(OD值)。 測定應在加終止液后15分鐘以內進行。
注意事項:
- 試劑盒從冷藏環境中取出應在室溫平衡15-30分鐘后方可使用,酶標包被板開封后如未用完,板條應裝入密封袋中保存。
- 濃洗滌液可能會有結晶析出,稀釋時可在水浴中加溫助溶,洗滌時不影響結果。
- 各步加樣均應使用加樣器,并經常校對其準確性,以避免試驗誤差。一次加樣時間控制在5分鐘內,如標本數量多,使用排槍加樣。
- 請每次測定的同時做標準曲線,做復孔。如標本中待測物質含量過高(樣本OD值大于標準品孔*孔的OD值),請先用樣品稀釋液稀釋一定倍數(n倍)后再測定,計算時請zui后乘以總稀釋倍數(×n×5)。
- 封板膜只限一次性使用,以避免交叉污染。
- 底物請避光保存。
- 嚴格按照說明書的操作進行,試驗結果判定必須以酶標儀讀數為準.
- 所有樣品,洗滌液和各種廢棄物都應按傳染物處理。
- 本試劑不同批號組分不得混用。
10. 如與英文說明書有異,以英文說明書為準。
計算:
以標準物的濃度為橫坐標,OD值為縱坐標,
在坐標紙上繪出標準曲線,根據樣品的OD
值由標準曲線查出相應的濃度;再乘以稀釋
倍數;或用標準物的濃度與OD值計算出標
準曲線的直線回歸方程式,將樣品的OD值
代入方程式,計算出樣品濃度,再乘以稀釋
倍數,即為樣品的實際濃度。
試劑盒性能:
1.樣品線性回歸與預期濃度相關系數R值為0.95以上。
2.批內與批見應分別小于9%和11%
保存條件及有效期:
1.試劑盒保存;2-8℃。
2.有效期:6個月
其它產品
9017815 Board, gripper, QIAC 2,940.00 CNY
9017734 Plasticware kit, IQ/OQ, EZ1 4,430.00 CNY
9015212 Z-Module 0.9mm Probe, BR8 RD 30,750.00 CNY
9015179 Cooling Block 48-tube, 2.0 ml, M48 16,140.00 CNY
9015155 Transportation kit, BR8000 14,980.00 CNY
9015083 Light Barrier, X-Dri., SamTrack, BR8 RD 13,670.00 CNY
9238475 2ml O-ring adapter tips, RapidPlate 243.00 CNY
9238239 Gasket, auto vac, SBS top BR8000/BR3000 902.00 CNY
9238224 Alignment Microspheres (10ml) 2,940.00 CNY
9240666 Nut, Flangeless,1/4-28, Cream, AP 1,300.00 CNY
9240661 Nozzle Kit, Dispense Head, AP 23,590.00 CNY
9240652 Vacuum Pump, Gast, 120V, AP96 32,370.00 CNY
9240622 Circuit Breaker, 8A, AP196/98 5,360.00 CNY
9240608 Fiber Optic Sensor, Main unit, AP98 10,250.00 CNY
9240575 Cable/Sensor,Purge Bottle, X26, AP96/196 7,020.00 CNY
9240569 ZLV Drawer Slide,Full Ext,Centrigue,AP96 51,370.00 CNY
9240567 Driven Gear, Centrifuge Locator, AP96 14,980.00 CNY
9240532 Cable, Shaker Encoder, AP98 9,110.00 CNY
9240509 Hard Drive, Programmed, Win XP, AP196/98 12,840.00 CNY
9239962 Upgrade App., BR MDx DSP CTM 48 PCR 15,140.00 CNY
9239562 Assy, Fan Mounting, 60 CFM (Coherent) 3,240.00 CNY
9019981 Vacuum test plate 1,380.00 CNY
9019484 Gasket, Carriage upper, CX1 797.00 CNY
9241210 RCS, Premium Cover Platform-only,2PM,1yr "This service agreement supplements the service coverage for the manual digene Hybrid Capture system) after the upgrade to a Rapid Capture System.
The Premium Cover RCS platform-only, 2 PM provides full service coverage for the Rapid Capture System. Costs for service visits are fully covered including travel, labor, and parts. The agreement also includes two annual preventive maintenance visits, with costs for labor and parts covered. With a Premium Agreement, there is a priority response time of 24 hours (1 working day)." 202,580.00 CNY
9241207 QIAsymphony SP, Full Agreement The Full Agreement QIAsymphony provides full service coverage for the QIAsymphony System. Costs for service visits are fully covered including travel, labor, and parts. The agreement also includes one annual preventive maintenance visit, with costs for labor and parts covered. With a Full Agreement, there is a priority response time of 48 hours (2 working days). 74,020.00 CNY
9241189 User Manual, QIAxcel 01/08 (WW) 3,560.00 CNY
9237330 Upgrade, BR & 4 ext. devices w. sched. Upgrade BioRobot with four approved integration devices using scheduling software 38,020.00 CNY
9237169 Bottle Waste 3,410.00 CNY
9233214 Tubing, waste, PVC, 8/12, (per m) 612.00 CNY
9237125 Upgrade App., DNeasy 96 "Take advantage of our instrumentation and molecular biology expertise to install
DNeasy 96 on your BioRobot System. The onsite protocol development visit includes
all travel and labor for the visit to install the standard QIAGEN DNeasy protocol, Plus a
DNeasy 96 Tissue Kit (4-plate) SAP# 69581" 14,780.00 CNY
9237107 Protocol Dev./Opt., on-site (3-days) The QIAGEN BioRobot Systems Protocol Development/Optimization On-Site Visit includes all travel and labor charges for a site visit up to 3 days by a QIAGEN Instrumentation Service Specialist to write and/or opimize protocols for the BioRobot System. Parts, consumable chemistries, and accessories not included. Custom protocols are the sole responsibility of the customer and neither warrantied nor guaranteed. 18,830.00 CNY
9232993 PCB, YZ-Connection, BR8 2,280.00 CNY
9232971 Syringe pump Board 15,910.00 CNY
9236410 Stacker, deepwell, TWI 8,240.00 CNY
9236362 Fuse 2A, 250VAC, Fast Acting 902.00 CNY
9236356 Sample Needle, long 2,940.00 CNY
9236352 Tubing, Valve to Pump 4,720.00 CNY
9236335 Sensor Distribution Board 7,160.00 CNY
9236157 User manual, RapidPlate 496.00 CNY
9236150 Locator Plate, 96 well&Reservoir,BR RP 1,500.00 CNY
9236148 Locator Plate, 384 well, BR Rapid Plate 3,000.00 CNY
9230679 Rack for reagents, Trough IBG 4,540.00 CNY
9021123 Valve Manifold, Upper, DCU 12,870.00 CNY
9021102 Skin Panel, Lower Left Side, DCU 18,110.00 CNY
9021049 Set, transparent panel, Qsym 17,110.00 CNY
9021026 Set, cables, transfer module, Qsym 1,550.00 CNY
9021012 Controller, Z Axis, VR, DCU 17,610.00 CNY
9020993 Pipettor Assembly, DCU 486,730.00 CNY
9020907 Cover, HEPA filter sys, SMC, QGX 6,570.00 CNY
9020905 UV light assembly, SMC, QGX 21,990.00 CNY
9020780 Notebook 1 XP 30,080.00 CNY
9020701 Clamp, table, single sided, C/S, C42 612.00 CNY
9020688 Cover - Bottom, PyroQ24 38,390.00 CNY
9020682 Pinch valve, PV02, QXT 31,550.00 CNY
9020640 Baseboard, front, AS, Cabinet Qsym 2,980.00 CNY
9020639 Baseboard, front, SP, Cabinet Qsym 3,890.00 CNY
9020365 Optical sensor, AS, Qsym 44,330.00 CNY
9020336 Pipetting head, 1 ch. (EXCHANGE), Cx2 8,510.00 CNY
9020315 PM kit, C12 & QIAgility (UV/HEPA), CG1 11,190.00 CNY
9020268 Packaging, box, QGY 5,490.00 CNY