油液取樣器簡介：
Introduction oil sampler:
油液取樣器也叫負壓油液取樣器，負壓取樣器，油液抽樣器，負壓采樣器，負壓油品取樣器能為精確進行油樣分析，在取樣時應特別仔細，防止塵土，雜質及前次抽樣時的殘油混入油樣。廣泛用于液壓元器件、液壓系統、液壓站、油缸、齒輪箱、變速箱、變壓器、汽輪機組、反應釜、馬達、發動機、泵、閥、輪轂、能器、過濾器、冷卻器、加熱器、油管、管接頭、油箱、壓力計、流量計、密封裝置等等的油樣抽樣及手動取樣。
Oil sampler is also called negative pressure oil sampler, negative pressure sampler, oil sampling device, negative pressure sampler, negative pressure oil sampler for precise analysis of oil sample, the sample should be especially careful, prevent dust, residual oil impurities and the previous sampling when mixed with oil. Widely used in hydraulic components, hydraulic system, hydraulic station, hydraulic cylinder, gear box, gear box, transformer, reactor, steam turbine, engine, motor, pump, valve, wheel hub, oil sampling capacitor, filter, heater, cooler, oil pipe, pipe fittings, oil tank, pressure gauges, flowmeters, sealing device etc. and manual sampling.
油液取樣器組成 ：
Oil sampler:
負壓油品取樣器包括一支負壓型抽油器和一次性使用的NAS 1638軟管與NAS 1638清潔瓶（50，100ml、250ml、500ml等規格任選），可有效防止油液粘附油搶和外界雜質污染油樣。油液取樣器由特種材料制造，表面經過鍍鋅防銹處理，耐油、防水、防侵蝕，美觀耐用。
Negative pressure oil sampler comprises a vacuum pumping device and a disposable NAS 1638 and NAS 1638 hose clean bottle (50100ml, 250ml, 500ml and other specifications optional), can effectively prevent the oil adhesion oil grab and external contamination of the oil sample. Oil sampler made of special material, the surface after galvanized processing, oil resistant, waterproof, anti erosion, beautiful and durable.
油液取樣器使用方法:
Oil sampler use method:
1．將油槍前端的圓螺母擰松一圈，將軟管穿過螺母，然后擰緊螺母并固定油槍接頭及軟管。（軟管伸出油槍接頭下端1cm,以免油槍接頭和油槍內部進油污染）
1 round nut oil gun in front of the loose circle, the hose through the nut, then tighten the nut and fixed gun fittings and hose. (hose out gun joint is 1cm, so as to avoid internal oil gun oil gun oil inlet joint and pollution)
2．把油樣瓶擰到油槍接頭上。（應趁油溫高時抽取油樣，例如在作業結束后抽樣。每次取樣條件應盡量相同）
2 the oil bottle is screwed to the gun joint. Should use the oil temperature high extraction (oil, for example in operation after the end of sampling. Each sampling conditions should be the same)
3．如果油箱裝有油尺，可抽出來，再將軟管伸入油中，如果油箱裝有油位螺噻，則擰下來，再把軟管伸入油中。（一般，軟管伸入油中深度約50mm。這樣，軟管就不致吸進任何沉積物;因為軟管是盤卷存放的，如果原樣使用有會夠不到油面，這時可在用前拉直到所需長度;如果軟管太長，可切成合適的長度，以保證減少吸油阻力和順利抽油）
3 if the tank is equipped with the oil dipstick, pumping out, then the hose into the oil, if the tank is equipped with oil Lo Sai, screw down, then put into the oil hose. (in general, hose into the oil in the depth of about 50mm. In this way, the hose would not in any sediment; because the hose is a coil storage, if used as they have not enough oil, and can be used in front straight to the desired length; if the hose is too long, can be cut into suitable length, with a pledge to reduce oil resistance and smooth sucker)
4．將油槍手柄推到底，然后用膠套蓋住油槍體前端的小孔，同時把油槍手柄往回拉，油瓶內就會形成真空，使油順著軟管流入油瓶。（如果如上操作，油槍一次行程，抽不足所需油量，要松開蓋住膠套的姆指，再朝前推油槍手柄，然后重復抽油操作）
4 the gun handle is pushed to the end, and then use the small rubber sleeve cover the gun body front, at the same time the gun handle is pulled back, will form a vacuum bottle, so that the oil into the bottle through the hose. (if the above operation, gun one stroke, pumping and lack the required oil quantity, to loosen the cover rubber sleeve thumb, then forward oil gun handle, and then repeat the pumping operation)
5．把油抽至油瓶上XXml標記處，不要使油瓶抽滿油。
5 the oil pump to the XXml marking bottle, do not make the oil pumping with oil.
6．從油槍接頭上擰下油瓶，裝上內蓋，注意不要混入塵土，（外界雜質。然后擰緊外蓋，瓶蓋要擰緊密）
6 from the gun joint unscrew the bottle, mounted on the cover, not mixed with dust, (external impurities. Then tighten the outer cover, bottle cap screw tight)
7．zui后，用干凈的布或紙擦干軟管端頭。擰松圓螺母，把軟管從螺母中抽出。（每次抽油后，要換用新的軟管）
7 finally, with a clean cloth or paper wipe the hose end. Unscrew the round nut, the hose is extracted from the nut. (each pumping, to be replaced with a new hose)
備注：配套性：可配套各類油液污染取樣、顆粒檢測取樣、清潔度分析采樣、油液監測采樣、油液分析采樣、常規取樣。
Note: supporting: can be matched with various oil contamination sampling, particle detection sampling, cleanliness sampling, sampling, analysis of oil monitoring oil sample analysis, the conventional sampling.
油液取樣器材質：超硬鋁合金；
Oil sampler material: aluminum alloy;
油液取樣器采樣流量范圍：0.5L/min ；
Oil sampler sampling flow range: 0.5L/min;
油液取樣器連續工作時間：1000min；
Oil sampler continuous working time: 1000min;
油液取樣器執行標準：GBT 17489
Oil sampler executive standard: GBT 17489
油液取樣器規格：50ml、100ml、250ml、500ml（此規格指清潔瓶）
Oil sampler specifications: 50ml, 100ml, 250ml, 500ml (this specification refers to clean the bottle)
軟管長度：可定制。
Hose length: can be customized.
油液取樣器優勢性描述：
Oil sampler advantage description:
1、使用輕便，無噪音；
1, the use of light, no noise;
2、用戶根據實際清潔度要求選用配套的清潔瓶（清潔瓶等級分為NAS 0級、1級、2級、3級、4級）；
2, according to the actual user clean bottle cleaning requirements choose matching (clean bottle grade NAS is divided into 0 levels, level 1, level 2, level 3, level 4);
3、用戶可根據自己的采油量來選擇取樣瓶的大小（清潔瓶的規格：50ml、100ml、150ML、200ML、250ml、500ml）；
3, the user can choose the sampling bottle size according to the oil production your (clean bottle specifications: 50ml, 100ml, 150ML, 200ML, 250ml, 500ml);
4、配套隨機攜帶的NAS 1638清潔管和NAS 1638清潔瓶更方便您的使用。
4, supporting the onboard NAS 1638 and NAS 1638 clean pipe cleaning bottle more convenient for you to use.
關于更多 油液取樣器 詳細資料請您
For more oil sampler details please call your advice