DLD1-2電磁離合器詳細介紹
1、簡介（Applications）
DLD1系列系無滑環干式，通電型工作的單片電磁離合器，線圈不旋轉，一個摩擦付，結構緊湊，傳遞力矩大，響應迅速，無空載損耗。
適用于高頻動作的機械傳動系統，可在主動部分運轉的情況下，使從動部分與主動部分結合或分離。廣泛適用于包裝機械、印刷機械、紡織機械、輕工機械、及辦公機械中。
DLD1Clutches are singledisc clutches for dry operation, without sliping the coil not rotating. High transmitting torque, quick response and no drag torque.
They are widely used in packing machines, printing machines, textile machines etc...., to realize the dricen and driving shaft while the latter is running.
2、主要性能參數：Main Technical Data
| 規格Specifications 數據Contents | DLD1-0.6 | DLD1-1.2 | DLD1-2.5 | DLD1-5 | DLD1-10 | DLD1-16 | DLD1-25 | DLD1-32 | DLD1-50 | DLD1-100 |
| 額定力矩（N.m） Rated Braking Torque | 6 | 12 | 25 | 50 | 100 | 160 | 250 | 320 | 500 | 1000 |
| 額定功率P20℃（W） Rated Power | 13 | 16 | 20 | 32 | 40 | 45 | 54 | 60 | 80 | 100 |
| 額定電壓（V dc） Rated Voltage | 24 | 24 | 24 | 24 | 24 | 24 | 24 | 24 | 24 | 24 |
| 接通時間（ms） Connecting Time T1 | 55 | 75 | 120 | 140 | 230 | 250 | 303 | 380 | 450 | 505 |
| 斷開時間（ms） Disconnecting Time T2 | 15 | 25 | 35 | 45 | 60 | 90 | 170 | 200 | 260 | 330 |
| 允許zui高工作轉速（rpm） Allowable Max Speed | 3600 | 3600 | 3000 | 3000 | 2500 | 2500 | 2500 | 2000 | 2000 | 1500 |
3、外形及安裝尺寸：Overall and lnstallation Dimensions
| 尺寸 型號 | D1 | D2 | D3 | D4 | D5 | D6 | D7 | D8 | D9 | M | d | L | L1 | L2 | L3 | L4 | L5 | L6 | L7 | b | b1 | h | δ |
| DLD1-0.6 | 80 | 72 | 35 | 68 | 50 | 38 | 12 | 4-4.3 | 3-4.1 | M4 | 15 | 24 | 3.5 | 18.5 | 28.5 | 20 | 22.5 | 15 | 14 | 5 | 4 | 17.3 | 0.3 |
| DLD1-1.2 | 105 | 95 | 42 | 90 | 66 | 45 | 15 | 4-5.5 | 3-4.1 | M6 | 20 | 27 | 5 | 25 | 35 | 25 | 24 | 20 | 16 | 6 | 5 | 22.8 | 0.3 |
| DLD1-2.5 | 130 | 110 | 52 | 112 | 80 | 55 | 20 | 4-5.5 | 3-5.2 | M6 | 25 | 31 | 7 | 32 | 44 | 30 | 28.5 | 25 | 18 | 8 | 5 | 28.3 | 0.4 |
| DLD1-5 | 158 | 147.5 | 62 | 145 | 101 | 64 | 25 | 6-5.5 | 3-6.2 | M6 | 30 | 36 | 8.5 | 38.5 | 56.5 | 40 | 30.7 | 30 | 20 | 8 | 6 | 33.3 | 0.4 |
| DLD1-10 | 190 | 175 | 80 | 169 | 120 | 75 | 30 | 4-9 | 3-8.2 | M8 | 35 | 38 | 9 | 47 | 66 | 50 | 34.5 | 38 | 35 | 10 | 8 | 38.3 | 0.5 |
| DLD1-16 | 230 | 215 | 100 | 213 | 158 | 90 | 40 | 4-9 | 3-10.2 | M8 | 43 | 44 | 11 | 56 | 80 | 59 | 40 | 45 | 40 | 12 | 10 | 46.3 | 0.5 |
| DLD1-25 | 270 | 258 | 110 | 245 | 182 | 98 | 40 | 4-9 | 3-10.2 | M8 | 50 | 48 | 12.5 | 60.5 | 81.5 | 59 | 44 | 48 | 40 | 14 | 12 | 53.8 | 0.6 |
| DLD1-32 | 290 | 270 | 120 | 167 | 210 | 118 | 45 | 4-11 | 3-12.2 | M10 | 55 | 51 | 12.5 | 67.5 | 92.5 | 70 | 47 | 55 | 40 | 16 | 14 | 59.3 | 0.6 |
| DLD1-50 | 310 | 290 | 130 | 286 | 248 | 125 | 50 | 4-11 | 4-12.2 | M10 | 60 | 55 | 13.5 | 73.5 | 99.5 | 75 | 50 | 60 | 45 | 18 | 16 | 64.4 | 0.8 |
| DLD1-100 | 440 | 420 | 200 | 424 | 315 | | | 4-12.5 | 4-16.2 | M12 | 70 | 66 | 19 | 95 | | | 56 | 76 | | 20 | | 74.9 | 0.8 |
4、安裝：Installation
安裝注意事項 Warning
●摩擦片及銜鐵表面不得有油污，必須保持清潔；
Friction disc and armature surface should be kept clean and free of grease.
●安裝離合器必須保證同軸度不大于0.1mm；
The coaxial degree should not exceed 0.1mm.
●與離合器配合的軸孔與軸精密度為H8/h7
Fit h7 is recommended so that the brake can be fitted easily and without demange on to the shaft.
●離合器主、從動側需固定，不允許有軸向竄動，同時必須保證工作氣隙“δ”
Not allowed to move on axial direction. Airgap should be kept in “δ”.
