150噸立式液壓打包機
配用動力：15KW，
臺時產量：3-5個包塊，
包重：200-800KG，
油缸：Φ160*2支，
150噸立式雙缸設計
型號：150
公稱壓力主缸KN：1500
液體*大工作壓力MPa:18
料箱尺寸長1100mm,寬700mm,高:1400mm
包塊尺寸:長1100mm*寬:700 *高:(1000）mm
包塊密度kg/m3：≥1000
單次循環時間S：45
電機功率KW：15
油缸行程：1200MM
機器外形尺寸mm：長1700*寬1400*高3900。
整機重量kg；5500.
150噸液壓打包機使用說明：
本廠150噸液壓打包機使用68#液壓油，連接電源三相380V，額定電流為25A，安裝時要有接地保護，電機要根據所示方向運轉才能啟用，否則不能啟動。油箱加入120公斤的液壓油方可啟動使用。但當氣溫降低時液壓油濃度大，機內的濾清器不能起到過濾作用，這時必須將濾清器拆出，待溫度恢復后，方可生新安裝使用。（注：濾清器應每月清洗1-2次）。
溢流筏-控制該機的壓力開關,旋轉調壓手轉向右轉為增壓，向左轉為減壓，出廠前已調整好壓力。但在使用過程中調壓手輪可能有變位現象，導致壓力升高或降低，這時需要生新調節壓力，調壓時應在運轉中進行，同時把壓板降至*低位置，調整溢流筏的調壓手輪，調整壓力不能高于或低于壓力表所示的范圍，*佳壓力的OMPA（100KG/1cm2）。旁桿-增強壓的剛性和起導向作用，每次使用前應加油，起潤滑作用。
行程開關-控制該機的啟動和停止的作用，因此要經常檢查、維修、保養。手動轉向閥-控制壓板向上向下，停止的開關。
1、手動轉向閥打向下檔位時壓板自動向下工作，當廢紙壓到結實狀態時，那阻力大于壓力：壓板不能再向下壓，應把手動轉向閥打向空檔位置，停止加壓，如果長期處于加壓狀態，會導致液壓，電機、油泵長時間處于超負荷狀態而使各機件損壞。
2、手動轉向閥打向升檔位置，壓板自動向上升到*高的位置，由行程開關控制自停，這時應把手動轉向空檔位置。完成一個工作程序。
液壓打包機使用說明書：
一、150噸液壓打包機安裝步驟
1、本機必須平穩放在混凝土上，基礎視當地情況決定。
2、檢查油箱底部放油口是否已關閉，確定關閉后再打開油箱頂部加油口密封蓋。
注入約90KG,68#液壓油，液壓油排號視當地氣溫及使用標準決定。[注！如果機型在60T以上，新機時必須分兩次注油，**次注入液壓油高度至油尺頂部（藍**線）。待壓板下壓至底部再加注液壓油至油尺底部（紅**線）詳細見操作說明4]
3、安裝好本機電源線,電壓及頻率視當地電源決定，（注！電機和電器配件的電壓及頻率已按客戶訂購機器時的要求配置安裝好）常規采用三相四線制，其中三條帶電源線分別接入電相內相應的三個接線位，（圖7左）另一條為接地防漏電保護線，應緊接機體外露金屬表面，以防電器漏電傷人。
二、150噸液壓打包機操作方法：
1、通入電源：把電箱內空氣開關（本機總開關）合上，先檢查三相電源電壓是否正常，（用儀表或探電筆測試）關閉電相門，查看電相門板表面紅色電源指示燈是否亮起。
2、啟動電機：把手動換向閥手柄（付圖3）往下推至*底位（機體附有操作圖標），然后把啟動按鈕NO按下（圖5右下），（注：如裝有急停開關機型的請把急停開關按箭頭方向右旋，急停開關彈出即可），（圖5右上）如正常情況下電機啟動。
3、 檢看電機轉向：（圖8）電機啟動后，手動換向閥手柄在*下位時，如壓板不能往下移。這時請必須立即查看電機旋轉方向是否正確，電機旋轉方向必須按箭頭指示方向一致。如果電機轉向相反時則機器不能正常使用，這時應把手動換向閥手柄往上拉至中檔位。然后按下停止按鈕OFF（或急停開關按下）停止電機運轉。切斷輸入總電源，把三相電源線其中二相線互換再接上即可。再按操作1和2重新操作，（注！必須確定電機轉向是否與箭頭指示方向一致。）
4、注入油量的關健：當壓板正常往下移時，壓板在**次移動，移動速度是不均勻的。待壓板移至底部或移動中突然停止又或移動中噪聲加大，這種情況下應先把手動換向閥手柄往上拉至中位，把停止開關OFF或急停開關按下，停止電機運行。再仔細查看油箱儲油量是否足夠，如油量底于油箱高度一半時，證明油量不足，這時應再次往油箱注入適當液壓油。這次加油量應加至油位尺*底界線（紅**線）即可。150噸液壓打包機操作方便， 接上電源后打包 , 專用于一切輕泡、松散物料的打包。可應用于棉、羊毛、廢紙、廢紙箱、廢紙板、紗線、塑料、布匹、編織袋、針織絨、麻、麻袋、毛條、毛球、繭、蠶絲、啤酒花、麥柴、草、廢塑料袋等一切輕泡、松散物料。包型緊湊，整齊美觀，可大幅降低運輸成本，是棉產區、紡織企業、超市、服裝廠、廢舊物資回收業和其他各種輕工業企業的生產工具 。
150 tons of vertical hydraulic balers
Scrap balers,
Equipped with power: 15KW,
Taiwan when the output: 3-5 mass,
Package weight: 200-800KG,
Cylinder: Φ160 * 2,
Easy to operate,
Connected to the power after packaging, dedicated to all light foam, loose material packaging. It can be used in cotton, wool, waste paper, waste paper box, waste paperboard, yarn, plastic, cloth, woven bag, knitted cashmere, hemp, sack, top, hair ball, cocoon, silk, hops, , Waste plastic bags and all the light foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises.
150 tons of double cylinder hydraulic balers
Model: 150
Nominal pressure master cylinder KN: 1500
Liquid maximum working pressure MPa: 18
Box size 1100mm long, width 700mm, height: 1400mm
Bulk size: Length 1100mm * Width: 700 * Height: (1000) mm
Mass density kg / m3: ≥ 1000
Single cycle time S: 45
Motor power KW: 15
Cylinder travel: 1200MM
Machine dimensions mm: length 1700 * wide 1400 * high 3900.
Machine weight kg; 5500.
Instructions for use:
The factory is equipped with 68 # hydraulic oil, connected to the power supply three-phase 380V, rated current of 25A, the installation should be ground protection, the motor should be operated in accordance with the direction shown to be activated, or can not start. The tank to join the 150 kg of hydraulic oil can be used to start. But when the temperature drops when the hydraulic oil concentration, the machine can not play a filter filter, then the filter must be removed until the temperature is restored before the new installation and use. (Note: the filter should be cleaned 1-2 times per month).
Overflow raft - control the machine's pressure switch, rotary pressure hａnd turn right to pressurized, turn left to decompression, the factory has been adjusted before the pressure. But in the course of the use of pressure handwheel may have a displacement phenomenon, resulting in increased or decreased pressure, then need to add a new regulation of pressure, pressure should be carried out in the operation, while the pressure plate to the lowest position, adjust the overflow Rafts of the pressure regulating handwheel, the adjustment pressure can not be higher or lower than the pressure gauge shown in the range of optimum pressure for OMPA (100KG / 1cm2). Side bar - to enhance the rigidity of the pressure and play a role, each should be used before the fuel, from the lubrication.
Stroke switch - to control the machine's start and stop the role, so often check, repair, maintenance. Manual steering valve - control the pressure plate up and down, stop the switch.
1, manual steering valve to play down when the pressure plate automatically down work, when the waste paper to a strong state, that resistance is greater than the pressure: the pressure plate can not be pressed down, the manual steering valve should be turned to neutral position, stop Pressurized, if the long-term pressure state, will lead to hydraulic, motor, pump for a long time in a state of overload and damage to the parts.
2, manual steering valve to the upshift position, the platen automatically rose to the highest position, controlled by the trip switch from the stop, then the manual should be turned to the neutral position. Complete a working procedure.
Hydraulic baler instructions:
First, the installation steps
1, the machine must be placed on the concrete, the basic depending on the local situation.
2, check the bottom of the fuel tank is closed, to determine the closure and then open the top of the tank filling port seal.
Injection of about 90KG, 68 # hydraulic oil, hydraulic oil row number as the local temperature and the use of standards. [Note! If the model is above 60T, the new machine must be filled with oil twice, the first time into the hydraulic oil height to the top of the dipstick (blue line). Press the press down to the bottom and then add the hydraulic oil to the bottom of the dipstick (red border) see the operating instructions in detail 4]
3, the installation of the local power cord, voltage and frequency depending on the local power supply decision, (Note! Motor and electrical parts of the voltage and frequency of customer orders have been ordered to install the machine installed) conventional three-phase four-wire system, three With the power cord, respectively, into the electrical phase of the corresponding three wiring bits (Figure 7 left) and the other for the ground leakage protection line, should be exposed to the body exposed metal surface to prevent electrical leakage wounding.
Second, the operation method:
1, access to power: the air box inside the air switch (the main switch) to close, first check the three-phase power supply voltage is normal, (with a meter or probe pen test) to close the electrical phase door, see the power of the door surface red power Whether the indicator light is on.
2, start the motor: the manual valve handle (pay Figure 3) down to the bottom (the body with the operation icon), and then press the button NO button (Figure 5 lower right), (Note: if installed There are emergency stop switch models, please put the emergency stop switch in the direction of the arrow, the emergency stop switch can pop up), (Figure 5 on the right) as normal under the motor start.
3, check the motor steering: (Figure 8) After the motor starts, manual valve handle in the lowest position, such as the pressure plate can not move down. In this case, you must immediately check whether the direction of rotation of the motor is correct and the direction of rotation of the motor must be in the direction indicated by the arrow. If the motor turns to the opposite when the machine can not be used normally, then the manual valve handle should be pulled up to the mid-range position. Then press the stop button OFF (or the emergency stop switch is pressed) to stop the motor from running. Cut off the total input power, the three-phase power cord which can be connected to the two-phase line. And then press operations 1 and 2 to re-operate, (Note! Must determine whether the motor steering direction is consistent with the arrow.)
4, into the fuel of the key: When the pressure plate down the normal move, the pressure plate in the first move, the movement speed is not uniform. To be pressed to move to the bottom or move suddenly stop or move the noise increases, in which case the manual valve should be pulled up to the middle of the handle, stop the switch OFF or emergency stop switch, stop the motor run. And then carefully check the tank oil storage is sufficient, such as oil at the end of the fuel tank height of half, to prove that the amount of oil, then again should be injected into the tank appropriate hydraulic oil. The amount of fuel should be added to the bottom line of the oil level (red line) can be.
東莞市天天自動化設備有限公司是專業從事粉體輸送技術研發，制造粉體輸送設備，公司**吸收國內外同類產品的*技術，公司設計上乘，加工裝備精良，生產工藝*。為用戶提供智能自動化輸送設備，吸料機、真空加料機、真空上料機、氣力輸送機，供料系統等系列產品，產品質量可靠，性能穩定。是一家以粉體輸送自動化技術為核心,致力于全產業智能產品及服務的高科技企業，是粉體處理*全的廠商之一，作為工業4.0的踐行者與推動者，公司現形成以自主核心技術、核心部件、產品及粉體行業系統解決方案為一體的完整全產業價值鏈，致力于打造數字化物聯新模式，成長性行業。 伴隨著智能時代的到來，天天自動化**推行產業、平臺戰略，打造集技術、人才于一體**與產業生態圈,實現智能產業裂變式發展，助力“中國制造2025”。不忘初心，實業報國，天天自動化將以智慧和情懷，為共建美好的智能互聯世界，砥礪奮進！天天自動化經營宗旨：百年企業，，專注粉體輸送行業，做粉體專家，不斷**，以追求人類環保安全生產為己任。與時俱進，勇于探索，廣泛合作，不斷超越，實現**粉體處理，制造上等產品，如同時間原子鐘一樣停止的工作，打造品牌的愿景。為國家創豐厚收益，為員工謀良好發展，為社會盡更多責任。天天自動化使命**行業發展 推動產業進步 提升生活品質天天自動化的遠景 致力于成為國際上等的高技術公司 從經濟一體化的角度看，不但要看到世界性的中國高技術產業市場，更要看到*產業的市場，對天天自動化而言，不僅要在國內市場的競爭中搶占，保持的穩步增長，成為客戶優選的*裝備制造品牌。更要實施“走出去”的國際化戰略，敢于同強大的對手在市場范圍內展開競爭，搶占進制造的。通過對國內市場的占有和對國際市場技術與產品的輸出，逐步走向產業內的多角化經營，*大程度地實現規模效益，增強企業的國際競爭力，發展成為與國際同步乃至*的，以*制造技術為核心的國際化高技術產業。天天自動化財富觀 君子愛財、取之有道財富源自員工的忘我勞動、源自股東的充分信任、源自協作者的鼎力相助，源自國家、社會的全力支持，財富之于天天自動化是一切相關人群工作成果的直接體現。天天自動化以追求經營利潤的增長為目標，更以謀求企業與社會的雙贏為己任，在注重經濟效益的同時，更加注重企業的社會效益，尊重游戲規則、信守承諾，以誠信經營之大道獲取天天自動化經濟與社會效益的增加。天天自動化一直認為：創業難、守業更難。“百年基業損于一旦”在市場競爭中并不罕見，市場中沒有永遠成功的企業，我們只有不斷尋求開拓、**才能實現天天自動化的可持續發展。天天自動化競爭觀 競為體、合為道 完善的競爭機制是天天自動化再發展的加速器。對內，天天自動化提倡員工間積極向上，公開、公平、公正的競爭，良好的競爭氛圍是天天自動化不斷**的催化劑；對外，要勇于參與國內、國際市場競爭，在競爭中不斷發展、壯大，使天天自動化充滿生機與活力。任何企業的發展都不可能*依靠自有資金和資源。天天自動化堅持以合作拓展空間、以合作促進發展的經營思路，增強業界廣泛的交流與合作，優勢互補，資源共享，致力于共同發展。天天自動化市場觀 市場是創造出來的 市場可以沒有企業，但企業不能沒有市場，而市場則源自客戶的青睞。天天自動化的存在是追求**達已，成已為人的過程，是幫助客戶獲得成功的過程。天天自動化人并不單單追求企業的經濟收益，更為重要的是實現了多少客戶的成功，體現了多少社會價值。我們在滿足市場的同時，更要善于利用新技術、新產品創造市場，善于發掘客戶的潛在需求，只有敢為人先，不斷**，才能創造更大的成功市場。天天自動化服務觀 三心兩意 三心：用心——竭盡所能，想客戶所想、急客戶所急；專心——心做好工作，切實解決客戶問題；誠心——對客戶要真誠守信，不欺瞞客戶；兩意：為了客戶滿意——為客戶服務是天天自動化不斷發展、獲得成功的基礎，作為現代化企業，我們不僅要建立一切為了客戶的經營理念，更要強調公司內部互為客戶的服務觀念。為了員工滿意——沒有滿意的員工就沒有滿意的客戶。在質量上，天天自動化崇尚上乘主義——沒有*好、只有更好，以細致出精品、以專業鑄品質，永遠追求以更好的質量贏得客戶的*滿意。
150噸液壓打包機 產品信息
