100G ZR4 80km QSFP28 Transceiver Hot Pluggable, Duplex LC Connector, EML+PIN with SOA Single mode DDM
FIBERWDM’s QSFP28 100G ZR4 RQ-100G-ZR4 is designed for 80km optical communication applications. This module contains 4-lane optical transmitter, 4-lane optical receiver and module management block including 2 wire serial inter-face. The optical signals are multiplexed to a single-mode fiber through an industry standard LC connector. A block diagram is shown in Figure 1.
Absolute Maximum Ratings
| Parameter | Symbol | Min. | Typical | Max. | Unit |
| StorageTemperature | TS | -40 |
| +85 | °C |
| SupplyVoltage | VCCT, R | -0.5 |
| 4 | V |
| RelativeHumidity | RH | 0 |
| 85 | % |
Recommended Operating Environment
| Parameter | Symbol | Min. | Typical | Max. | Unit |
| Case operatingTemperature | TC | 0 |
| +70 | °C |
| Supply Voltage | VCCT, R | +3.13 | 3.3 | +3.47 | V |
| Supply Current | ICC |
| 1200 | 1800 | mA |
| Power Dissipation | PD |
|
| 6.5 | W |
Electrical Characteristics(TOP = 0 to 70 °C, VCC= 3.13 to 3.47 Volts
| Parameter | Symbol | Min | Typ | Max | Unit | Note | ||
| Data Rate per Channel |
| - | 25.78125 |
| Gbps |
| ||
|
|
| 27.9525 |
|
| ||||
| Power Consumption |
| - | 4 | 6.5 | W |
| ||
| Supply Current | Icc |
| 1.2 | 1.8 | A |
| ||
| Control I/O Voltage-High | VIH | 2.0 |
| Vcc | V |
| ||
| Control I/O Voltage-Low | VIL | 0 |
| 0.7 | V |
| ||
| Inter-Channel Skew | TSK |
|
| 35 | Ps |
| ||
| RESETL Duration |
|
| 10 |
| Us |
| ||
| RESETL De-assert time |
|
|
| 100 | ms |
| ||
| Power On Time |
|
|
| 100 | ms |
| ||
| Transmitter | ||||||||
| Single Ended Output Voltage Tolerance |
| 0.3 |
| Vcc | V | 1 | ||
| Common mode Voltage Tolerance |
| 15 |
|
| mV |
| ||
| Transmit Input Diff Voltage | VI | 150 |
| 1200 | mV |
| ||
| Transmit Input Diff Impedance | ZIN | 85 | 100 | 115 |
|
| ||
| Data Dependent Input Jitter | DDJ |
| 0.3 |
| UI |
| ||
| Receiver | ||||||||
| Single Ended Output Voltage Tolerance |
| 0.3 |
| 4 | V |
| ||
| Rx Output Diff Voltage | Vo | 370 | 600 | 950 | mV |
| ||
| Rx Output Rise and Fall Voltage | Tr/Tf |
|
| 35 | ps | 1 | ||
| Total Jitter | TJ |
| 0.3 |
| UI |
| ||
Note:
1. 20～80%
Optical Parameters(TOP = 0 to 70°C, VCC = 3.0 to 3.6 Volts)
| Parameter | Symbol | Min | Typ | Max | Unit | Ref. | ||
| Transmitter | ||||||||
|
Wavelength Assignment | L0 | 1294.53 | 1295.56 | 1296.59 | nm |
| ||
| L1 | 1299.02 | 1300.05 | 1301.09 | nm |
| |||
| L2 | 1303.54 | 1304.58 | 1305.63 | nm |
| |||
| L3 | 1308.09 | 1309.14 | 1310.19 | nm |
| |||
| Side-mode Suppression Ratio | SMSR | 30 | - | - | dB |
| ||
| Total Average Launch Power | PT | 8 | - | 12.5 | dBm |
| ||
| Average Launch Power, each Lane |
| +2 | - | 6.5 | dBm |
| ||
| Difference in Launch Power between any two Lanes (OMA) |
| - | - | 3 | dB |
| ||
| Extinction Ratio | ER | 6 | - | - | dB |
| ||
| Transmitter Eye Mask Definition {X1, X2, X3, Y1, Y2, Y3} |
| {0.25, 0.4, 0.45, 0.25, 0.28, 0.4} |
| 1 | ||||
| Optical Return Loss Tolerance |
| - | - | 20 | dB |
| ||
| Average Launch Power OFF Transmitter, each Lane | Poff |
|
| -30 | dBm |
| ||
| Relative Intensity Noise | Rin |
|
| -130 | dB/HZ |
| ||
| Optical return loss tolerance |
|
|
| 20 | dB |
| ||
| Transmitter reflectance |
| - | - | 12 | dB |
| ||
| Receiver | ||||||||
| Total Damage Threshold | THd |
|
| 5.5 | dBm | 1 | ||
| Receiver Sensitivity per Lane | R |
|
| -28 | dBm |
| ||
| Average Power at Receiver Input, each Lane | R | -28 |
| -7 | dBm | 1 | ||
| LOS De-Assert | LOSD |
|
| -29 | dBm |
| ||
| LOS Assert | LOSA | -40 |
|
| dBm |
| ||
| LOS Hysteresis | LOSH | 0.5 |
|
| dB |
| ||
Note
1. Sensitivity is specified at BER@5E-5 with FEC
Order information
| Product Number | Data Rate(Gb/s) | Wavelength(nm) | Reach(km) | LD | Tx Power(dBm) | PD | Rx Sens(dBm) | Temperature(℃) |
| RQ-100G-ZR4 | 100 | 1310nm | 80 | LAN WDM EML | 2~6 | PIN+SOA | <-28 | 0~70 |
