進口圓盤式疏水閥-德國進口圓盤式疏水閥 
進口圓盤式疏水閥、進口蒸汽疏水閥、德國LIK型號結構、尺寸閥標準
德國萊克LIK圓盤式疏水閥
裝置剛啟動時，首先在較低的壓力下空氣和冷凝水流過疏水閥，通過入口孔托起閥片，再由出口孔排出，當壓力、溫度上升后，內壓上升，推動凝結水量增多，而增大流速，這時閥片下的靜壓降低，使閥片下落，蒸汽從出口孔中間由四周流向閥片和閥蓋之間的間隙，進入壓力室，將閥片壓在密封環上，關閉閥門。當壓力室的蒸汽溫度降低，開始冷凝，使壓力室內的壓力降低，進口壓力托起閥片，疏水閥開啟進行排水。
Disc Trap
When starting the device, firstly, the air and condensed water will flow across steam trap under rather low pressure, and lift valve plate through the entrance hole, and then discharge from the exit hole. After the pressure and temperature rise, the inner pressure will also rise, and cause increased amount of condensed water and increased flow rate, at the moment, the static pressure of valve plate declines which causes the drop of valve plate, and then, the steam flows from all directions via the exit hole into the gap between the valve plate and the valve cover. After steam enters the pressure chamber, it shuts down the valve by pressing valve plate onto the sealing ring. When the steam temperature inside the pressure chamber begins descending and the steam begins to congeal, the pressure declines in the pressure chamber, and the inlet pressure lifts the valve plate, and then the steam trap opens and discharges water.
優點：
1、結構簡單，容易安裝和維修，抗水擊。
2、抗水擊，對壓力突然變化沒有影響。
3、可用于過熱蒸汽系統。
4、可以使用高壓高溫的蒸汽管線。
Merits
1.Simple structure, easy installation and maintenance and water hammer resistant.
2.Water hammer resistant and no effect from abrupt change of pressure.
3.Adoptable for overheat steam system.
4.Adoptable for high-pressure and high-temperature steam pipes.
技術參數/Technique parameter
殼體壓力等級
Shell pressure grade    負荷泄漏率
Load leakage rate    使用介質
Used medium    殼體材質
Shell material    允許背壓率
Permitted backpressure rate
1.6～42MPA    0.3%    蒸汽、凝結水
Steam、Condensate water    鍛鋼、不銹鋼、合金鋼
Forged steel、Stainless steel、Alloy steel    50%
zui大工作壓差
Maximum operating pressure differential    使用過熱蒸汽
Use superheated steam    zui高允許溫度
Maximum allowable temperature    抗水擊
Resist    壓力變化范圍
Pressure change range
17MPA    優秀
Excellence    420~550℃    適應
Adaption    適應
Adaption
主要零件材料/The materials of primary accessories
零部件名稱Part and component name     材質Material
閥體、閥蓋Valve body、Valve cover    鍛鋼、不銹鋼、合金鋼Forged steel、Stainless steel、Alloy steel
閥片Valve plate    高鉻不銹鋼High chrome stainless steel
閥座Valve seat    STL合金STL alloy
過濾網Filtrating screen    不銹鋼Stainless steel