聚丙烯酰胺輸送泵EU600-P-W201螺桿2Cr13,襯套采用丁青橡膠
臥式單螺桿泵操作保養規定:Horizontal single screw pump operation maintenance provisions:
一、操作規程 1、檢查流程是否正確。 2、檢查聯軸器保護罩,地腳等部分螺絲是否緊固,有無松動現象。 3、軸承油盒要有充足的潤滑油,油位應保持在規定范圍內,油質是否完好。 4、檢查電壓是否在規定范圍內,外觀電機接線及接地是否正常。 5、用手盤動聯軸器,檢查泵內有無異物碰撞雜聲或卡死現象,并給予消除。 6、停車前需先停止電機運行,后關閉吸入管閥門,再關閉排出口閥門(防止干轉,以免擦傷工作表面)。A, operating rules 1, check whether the process is correct.2, check the coupling shield, whether the anchor parts such as screw fastening, the presence of loose phenomenon.3, bearing oil box should have plenty of oil, oil level should be kept within the prescribed scope, oil are in good condition.4, check whether the voltage is within the scope of the regulations, electrical wiring and grounding are normal in appearance.5, with the hand disc coupling, check there are no foreign bodies collide in the pump noise or jammed phenomenon, and to give away.Need before 6, parking to stop the motor running, after close the suction valve, then close the discharge valve (turn to prevent dry, so as not to scratch working surface).聚丙烯酰胺輸送泵EU600-P-W201螺桿2Cr13,襯套采用丁青橡膠,它是依靠螺桿與襯套相互嚙合在吸入腔和排出腔產生容積變化來輸送液體的。它是一種內嚙合的密閉式螺桿泵,主要工作部件由具有雙頭螺旋空腔的襯套(定子)
二、維護保養 1、檢查軸封及各接合密封面是否有泄漏; 2、檢查冷卻系統是否暢通,壓力、溫度是否在合理范圍; 3、檢查運轉的平穩性,是否有振動; 4、檢查機座螺栓是否松動; 5、長時間停車應排凈系統中的物料,氣溫較低時檢查防凍防凝情況。 2, 1, check the shaft seal and the maintenance of joint sealing surface whether there is leakage;2, check whether the cooling system is open, pressure, temperature is in the reasonable scope;3, check the operation stability, whether to have vibration;4, check whether the mounting bolts is loose;5, stop for a long time should be no net system of material, the temperature is lower check antifreeze anti coagulation conditions.
三、注意事項 1、啟動前一般應全開入口閥、出口閥,打開出口閥后,應盡快將泵啟動。嚴禁在沒有打開出口閥的情況下開泵(如果出口閥關閉,必須保證出入口連通閥全開)。 2、嚴禁在沒有灌泵的情況下長時間運轉。 3、出現下列情況立即停泵:嚴重泄漏、異常振動、異味、火花、煙氣、撞擊、電流持續超高等現象。 4、螺桿泵在運行過程中,軸承溫度不能超過環境溫度35℃,zui高溫度不得超過80℃. 1, before the start of the general considerations should be fully open the inlet valve and outlet valve, open the outlet valve, should will pump start as soon as possible.Is strictly forbidden in the absence of open the outlet valve opening pump (if the outlet valve closed, must ensure that the gateway connected valves).2, it is strictly prohibited in the absence of irrigation pump long time running.3, stop the pump immediay in the following circumstances: serious leakage, abnormal vibration, bad breath, a spark, flue gas, such as collisions, current ultra-high phenomenon.4, screw pump in the process of operation, the bearing temperature cannot exceed ambient temperature 35 ℃, the highest temperature should not exceed 80 ℃.單螺桿泵概述,它是依靠螺桿與襯套相互嚙合在吸入腔和排出腔產生容積變化來輸送液體的。它是一種內嚙合的密閉式螺桿泵,主要工作部件由具有雙頭螺旋空腔的襯套(定子)
油墨輸送泵 | G35-1V-W102單螺桿泵 | 深圳市芭田生態工程股份有限公司 |
輸送合成樹脂泵 | NYP50高粘度泵 | 廣東榕泰實業股份有限公司 |
輸送呋喃樹脂泵 | G40-1V-W102單螺桿泵 | 江蘇阿波羅復合肥有限公司 |
輸送灰膏泵 | 3GR70*2W2三螺桿泵 | 錯 |
輸送煤焦油泵 | 3GR50*4AW21三螺桿泵 | 云南鹽化股份有限公司 |
輸送涂料泵 | G35-1V-W111單螺桿泵 | 貴州久聯民爆器材發展股份有限公司 |
輸送棕櫚油泵 | 3GR42*6AW2三螺桿泵 | 江蘇安邦電化有限公司 |
輸送糖漿泵 | NYP-24-RU-M1-W51高粘度泵 | 中國藍星哈爾濱石化有限公司 |
輸送油脂泵 | G40-1P-W101單螺桿泵 | 安徽金禾實業股份有限公司 |
輸送柴油泵 | W5.1ZK65Z1M1W73 | 藍星清洗股份有限公司 |
聚氨酯提料泵 | W4.2ZK-78Z0M1W80 | 江蘇靈谷有限公司 |
輸送合成液壓油泵 | W6.4ZK75Z1M1W73 | 雙喜輪胎工業股份有限公司 |
聚氨酯提料泵 | NYP110-RU-M1-J-W51高粘度泵 | 昊華華東公司 |
輸送天然油泵 | 3GR42*4W21三螺桿泵 | 湖北凱樂科技股份有限公司 |
磨煤機螺桿泵 | 3GR42*4Aw21三螺桿泵 | 岳陽興長石化股份有限公司 |
磨煤機潤滑油泵 | 3GR36*6W21三螺桿泵 | 江蘇嘉盛品工業有限公司 |
輸送煤焦油泵 | 3GR36*4三螺桿泵 | 百合花集團有限公司 |
輸送粘膠液泵 | W5.1ZK78M1W73 | 浙江龍騰科技發展有限公司 |
輸送炭黑油泵 | GN50-1V-W112單螺桿泵 | 煙臺氨綸股份有限公司 |
輸送油泥泵 | G85-1V-W102單螺桿泵 | 浙江海越股份有限公司 |
輸送污水泵 | G25-1V-W102不銹鋼單螺桿泵 | 中藍有限公司 |
輸送稠油泵 | G135-1P-W101單螺桿泵 | 青島海晶集團有限公司 |
水輪機調速控制油泵 | 3G70*4C懸掛式三螺桿泵 | 陳村水力發電廠 |
螺桿具有單頭螺紋,其任意截面皆為半徑為R的圓,截面的中心位于螺旋線上且與螺桿的軸心線偏離一個偏心距e,繞軸旋轉且沿軸向移動而形成的頭數比Lobes:螺桿的定子的頭數T1比轉子的頭數T2多一個,即T1=T2+1.他們的比值成為頭數比。螺桿泵可以分為單頭(1:2)和多頭(2:3,3:4)等。頭數比越多,螺桿泵的輸出扭矩越大,轉速越低。反之,輸出的扭矩越小,轉速越高.襯套內表面具有雙螺紋,其任意截面為一長圓,兩端是半徑為R(等于螺桿截面半徑)的半圓,中間是長為4e的直線段。襯套的任意截面都是相同的長圓,只是彼此互相錯開一個角度。螺桿裝入襯套后,螺桿表面與襯套內螺紋表面之間形成一個個封閉的腔室,同時任意截面也被分成上下兩個月牙形工作室。當螺桿旋轉時,靠近吸入室的*個工作室的容積逐漸增大,形成負壓,在壓差的作用下液體被吸入工作室。When the screw rotates, the first studio near the suction chamber volume increases gradually, form the negative pressure, under the action of pressure difference, liquid drawn into the studio.隨著螺桿的繼續轉動,工作腔容積不斷增至zui大后,這個工作室封閉,并將液體沿軸向推向壓出室。As a continuation of the screw rotation, continuous working volume to maximum, the studio closed, pushed along the axial liquid and the pressure out of the room.與此同時上下兩個工作室交替循環地吸入和排出液體,因此液體被連續不斷地從吸入室沿軸向推向壓出室。,它是依靠螺桿與襯套相互嚙合在吸入腔和排出腔產生容積變化來輸送液體的。它是一種內嚙合的密閉式螺桿泵,主要工作部件由具有雙頭螺旋空腔的襯套(定子)
單螺桿泵(helical rotor pump;single-screw pump;mono pump)屬于轉子式容積泵,它是依靠螺桿與襯套相互嚙合在吸入腔和排出腔產生容積變化來輸送液體的。它是一種內嚙合的密閉式螺桿泵,主要工作部件由具有雙頭螺旋空腔的襯套(定子)和在定子腔內與其嚙合的單頭螺旋螺桿(轉子)組成。當輸入軸通過萬向節驅動轉子繞定子中心作行星回轉時,定子 — 轉子副就連續地嚙合形成密封腔,這些密封腔容積不變地作勻速軸向運動,把輸送介質從吸入端經定子 — 轉子副輸送至壓出端,吸入密閉腔內的介質流過定子而不被攪動和破壞。單螺桿泵分類:整體不銹鋼單螺桿泵,軸不銹鋼單螺桿泵。Single screw pump classification: overall stainless steel single screw pump, stainless steel shaft single screw pump.
選用泵的規格是根據被輸送液體的性質和流量、壓力來決定的,而泵的轉速則由輸送液體的粘度和腐蝕性、作為主要參數來選擇,才能保證泵可靠運行。泵的設計轉速為輸送清水或清水相類似的無腐蝕性液體時允許zui高轉速,在實際使用中因介質性質與壽命要求不同,選用時一般都應低于設計轉速。對高粘度和含顆粒介質,一般采用設計轉速的1/2-1/3 或更低些,低轉速對泵的磨損有利,但在使用后由于定子的磨損流量下降,這時可適當提高轉速,以補償流量下降也為常策。輸送介質的溫度應在 -10 ℃~80℃特殊情況可高達120℃。
泵的每級(定子的一個導程)正常壓力為 0.6Mpa,短時間(不超過30分鐘)內允許高達0.8Mpa,當磨損后在相同輸出壓力時的容積效率要逐步下降。泵送清水時zui高吸程為 8米,實際使用建議不超過6.5米,當泵送高粘度介質時,應以正壓吸入。